Question about Televison & Video

1 Answer

The KCP&L power comp.changed the meter and I lost power and now the tv will not turn on

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Televison & ... Master
  • 53,656 Answers

  • Open internal fuse
  • Power supply failure

Posted on Aug 18, 2019

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Muz series led flashes twice


58 volts is not enough to run a compressor either your meter / reading is wrong and there should be no voltage on compressor terminals when disconnected .

Nov 22, 2014 | Heating & Cooling

1 Answer

Mitsubishi tv customer service


i have a blinking green light and then the red lamp light comes on and stays. no picture no sound

Aug 07, 2013 | Televison & Video

1 Answer

Zenith Z50PJ240 powers on and turns off relays click while its doing this unplugged ysus and zsus no change unplugged comp board tv turns on red light goes out but will not power down then.


It becomes first a case of checking voltages to and from power supply first and then a guessing game---which board will you buy and try first?

Nov 06, 2012 | Televison & Video

1 Answer

Models: KCT, KCP Power Switching device: Standard Open- Transition 30 to 4000 Amps Programmed- Transition 150 to 4000 Amps Electrical Controls: MPAC 1000 Problem: Power went off, generator Started,...


try to find the manual , these units have a pre program set from the factory, dissconect the unit at the generator 1)battery terminal 2)main switch on generator 3) reconnect battery and turn on the switch,press auto,should reset

Jun 09, 2011 | Kohler Electrical Supplies

1 Answer

Lost entire picture, sound and everything else OK


check the invertor boards resistors they power the back lights
also check for any capactors that have blown (raised tops) they look little bateries

Dec 12, 2009 | Element Electronics FLX3220F 32 in. LCD TV

1 Answer

Mitsubishi WS-65315 plug in HD comp shows as 480i


Greetings,

In the input assignment menu make sure that the DTV (the only 1080 input on this tv) is set to Y/Pb/Pr and see if that fixes your issue with at least the HD-DVR.

BTW- the HDMI information "1080i HD can only be selected if TV has HDMI inputs". is not correct.

Feb 25, 2009 | Mitsubishi WS-65315 65" Rear Projection...

1 Answer

Power up then goes off


take your tv to a w/shop, it has variations at a power supply connect a avo meter and check for changes at the output of a supply.
i check capacitors change values
ii semi conductor lekages

Jan 26, 2009 | Zenith B25A02Z TV

1 Answer

Laptop's light is turning off!


This is going to be a problem with either the screen inverter, or the screen backlight. I would recommend have it diagnosed first to see which it is. You can test this yourself if you have an ohm meter, and a little technical know how.You will need to pull the screen bezel (the plastic piece around the front of the screen), the are screws hidden under the small round plastic sticky tabs on the bezel. Once you've removed the screws the bezel will snap off. Get it started at one side and work it up the rest of the way around, be careful not to break it ar the corners when lifting it off. Once the bezel is off you will see the inverter at the base of the screen. Power down the machine and disconnect the lead that goes to the screen. The power going into the inverter is very low, the inverter boosts the power back up to what the screen needs to work, so the power on the screen end will be significantly higher than the motherboard end. The voltage range differs machine to machine, so I can't tell you what it should be exactly, only that if it's the same or slightly higher from end to end, then it's bad. Now, inverters can be changed out, but backlight are part of the screen and cannot be change out. If it's a bad backlight, then the entire screen will need replaced.

Aug 22, 2008 | IBM ThinkPad R40 2897 Notebook

1 Answer

Lost signal


well overall the tv isn't too reliable but perhaps you have the input on comp(vga) if you do that it says no signal and shuts off, try changing the channel by click either the channel up or down button, or just press the input button.
that would be the easy fix, or your tv is just broken like so many others, myself included

Mar 21, 2008 | Polaroid FLM-1911 19 in. LCD Television

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76115 Answers

Ekse

Level 3 Expert

13434 Answers

Cindy Wells

Level 3 Expert

6004 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...