Question about Washing Machines

1 Answer

On electrulox washing maching h3 error what does that mean

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 39 Answers

If you have the Electrolux EWM2100 Washer, the EH3 error code has to do with the Voltage being too low, Power supply problems (incorrect / disturbance); PCB faulty.

Contact the warranty department or have your washer serviced.

Posted on Aug 24, 2019

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
blueextc3221
  • 15935 Answers

SOURCE: Getting error code F1 and don't know what it

F01 - There may be an internal problem with the control, attempt a Hard Reset.

Hard Reset - In some cases the control can be non-functioning or may not accept activation from the control panel. To clear and restart the control follow the these steps:

* Unplug or turn the circuit breaker off for 30 seconds.
* Reconnect the unit to the power source by turning the breaker back on or plugging the unit back into the wall outlet.
* Press the Pause/Cancel/Stop button twice to clear the "PF" in the display.
* Start a short cycle to check the operation of the machine by selecting a cycle and pressing and holding the start button until the machine starts.

The F01 generally indicates a failed electronic machine control board.
This error code can sometimes be caused by a glitch or power surge through the electrical lines.
You may be able to clear this code by unplugging the washer for 5 minutes.
If the code returns after plugging the washer back in, then the electronic machine control board will need to be replaced.

The procedure for accessing and replacing this control board is shown in this image...

http://media.fotki.com/1_p,wkwdftgtbkdgfrwxgtqsskgwtqkq,vi/ksrttqdqrxkssrqtgsd/1/1303472/5961857/image12917img-or.jpg

Be sure to unplug the washer before accessing internal components.
When you access the control board, I recommend transferring the wires from the old control board to the new replacement control board one connection at a time.
Once you have all of the wires transferred, remove the old control board and mount the new control board in the washer.
Reassemble and test the washer.

The "F01" error code indicates a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU.
The "F01" can also be displayed if the onboard "Pump Driver" fails to activate.
Generally in order to correct this failure will require replacing the CCU.
There is no way to test and verify if the control board has failed.
The technical data sheet basically states to replace the CCU.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WAT DUSE F42 MEAN ON A BOSCH WASHING MACHING


Hi,

It could mean there's a fault with the motor

Source: Bosch Error Codes Page

Dec 14, 2016 | Bosch Washing Machines

1 Answer

Samsung washer error code f1


What kind of detergent are you using? F1 in most cases means that the wrong type of detergent is being used. If it's a front-loader, you should be using h3 detergent.

May 21, 2012 | Samsung Clothes Washer Power Control Board...

2 Answers

F43


Hi.

If you have Bosch, Baumatic, or any other machine built by Bosch, then F43 is a motor issue:

Error F43 : Motor fault: do an emergency drain through the drain access in the front bottom side (see manual). Open door and check ig the drum rotates free when spin by hand. Disconnect power before performing maintenance.

Regards.

Ginko

Sep 14, 2011 | Washing Machines

1 Answer

Kenmore elite washer h3 has a f5 code flashing. what does it mean?


The F5 error code indicates a water temperature problem. The control board circuit is not recognizing a resistance change in the water temperature sensor.

You most likely have a loose connection at the tub sensor , or a bad heater.



Richard Roth

The FixYa Team

Aug 17, 2011 | Kenmore Washing Machines

1 Answer

What does code FDL mean? kenmore elite wash maching


You are getting and error code F-DL which means the main control board is sensing that the door is not locking. Most likely a problem with the door lock/latch assembly.

Feb 02, 2010 | Kenmore 45981 Washer

1 Answer

My washing maching will not spin and is giving an oe error


The LG error code OE simply means "the pump is blocked". Presumably the water isn't being emptied properly. As with all error codes it is possible that there is a cause other than the exact description in the error code explanation but basically this error means as far as the washing machine is concerned it thinks the water isn't pumping out. A pump, or filter blockage is the most common cause but it could be caused by other faults such as a faulty pump, or even a blockage in the drain hose or somewhere else in the system etc.


LG themselves have some information on this error code..

http://lgknowledgebase.com/kb/index.php?View=entry&EntryID=6273

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 12, 2009 | Washing Machines

2 Answers

Kenmore elite h3


I have an H3 washing machine and the rubber bellow lip that seals the front door from leaking has torn causing water to leak out. Can this bellow be repaired or easily removed and replaced without calling a service repairman.

Nov 25, 2007 | Kenmore Elite 45986 Front Load Washer

2 Answers

Error codes


if this is a fridgidaire washer, I guess it's a clogged coin catcher. You have remove the front access panel and clean it out. I am working on that now.

Nov 05, 2007 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85161 Answers

Brad Brown

Level 3 Expert

18087 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...