Question about Medical

1 Answer

Neck stoma covering - Medical

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Master
  • 29,140 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Miracle mate power head not getting power


Most likely you have a broken wire in the neck assembly, where the wand meets the floor nozzle. To check unplug the cord and remove wand from floor nozzle. On the neck, remove 3 small screws and slide the cover off the back of the neck. You will see 2 wires, one white and one black. Gently tug on each to see if if they are connected. If one is loose you have the problem, if not you will then have to remove the five screws that hold the cover on the nozzle body and trace the connection to the circuit board.

Aug 18, 2012 | Vacuums

1 Answer

I have a clogged fuel line (filter?) I do I remove the bushing without damaging it?


FUEL FILTER

(For 40/55/60/70/110/115/155/165 Models

Only)

1. Remove side cover screws using 5/16" nutdriver.

2. Remove side cover.

3. Pull upper fuel line off fuel filter neck (see

Figure 15 or 16).

4. Carefully pry bushing, fuel filter, and lower

fuel line (110/115/155/165 Models only) out

of fuel tank (see Figure 16).

5. Wash fuel filter with clean fuel and replace in tank.

6. Attach upper fuel line to fuel filter neck.

7. Replace side cover.

Jan 20, 2012 | Reddy Heater-70,000 BTU Kerosene w/T'stat

2 Answers

I just buy a vizio 32 razor led, and i want to mount in the wall so, the instructions says remove de 4 screws in the neck well i only see 2 and i remove them and stell cant remove de the neck


I've got the same problem. There are three screws in the neck and I don't want to remove them if that's not how to remove the neck. The manual says to remove the base and neck but only describes removing the base. Leaving the neck would be unsightly, to say the least.

Dec 12, 2010 | Vizio Televison & Video

1 Answer

Error e000019-0000 how to solve


Hi there,
on copiers like iR22/28/3300, E019 means that there is waste toner full.

On leftsideway of copier in lower left section, is cover with one scre. Remove cover and pull the bottle out. Dump out the waste toner, clean bottle and most important the neck of bottle, because on that two small circles on neck copier reads the amount of waste toner.
Error could arrise eaven if the neck is only dirty.

Permanent solution is to disconnect the connector above waste toner box. But be sure to clean the bottle every 50000-70000 copies.

Hope that helped.

May 09, 2010 | Canon imageRUNNER 3300 All-In-One Laser...

1 Answer

How do i replace the oil fiter neck from a 3.8 buick


I have a 1999 3.8L Buick engine. The filler neck has a large o-ring and twists into place on the front top of the valve cover. The filler neck only needs about a half-turn to be in posiiton. It is keyed with pastic tabs on the neck so it only goes in one-way. Let me know fi this helps or you need more infromation.

May 03, 2010 | 1999 Buick Regal

2 Answers

Canon 2200 error code 000019-0000


This error code means that the waste toner bottle is full. Most likely it is not full, the waste toner bottle neck gets some waste toner on it and it blocks the sensor.... It is a bad design by Canon. The waste toner bottle is on the Left side of the copier, toward the rear of the copier. The cover is held in by one screw, the cover comes off and the Waste Toner Bottle is inside. Turn the copier OFF by the Main Power Switch on the Right side of the copier. Carefully, dump the waste toner out in a plastic bag. Hopefully, without any holes in it. Wipe OFF all the toner OFF the neck of the bottle. You will see what looks like a DOT on each side of the neck.Make sure the inside and out side is clean. Reinstall the bottle and cover and then turn the Main power ON and the Code should be gone. Good Luck....

Mar 29, 2009 | Canon imageRUNNER 2200

2 Answers

2004 and 2001, are parts interchangeable?


Yes they are as long as the Motors are Similar.

Jan 22, 2009 | 2004 Ford Crown Victoria

2 Answers

Massaging neck rest question


The massaging neck rests usually offers you two relaxation therapies: variable speed vibration massage to customize massage intensity and heat. Some of this devices even have a "comforting sounds" option (which makes relaxing sounds). Besides that most of the massaging neck rests offers the same featurs. They wrap comfortably around your neck and shoulders, supporting your head in a comfortable position (Usually - memory-foam filling and a soft fabric cover). Hand-held control adjusts the vibrations to your specific comfort level, without having to stop the massage. Includes plug-in AC adapter, or you can use four AA batteries

Aug 27, 2008 | Comfort Products 60 2702 Fleece Pamper...

Not finding what you are looking for?
Medical Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Medical Experts

Gene Pitts

Level 2 Expert

159 Answers

Argospete
Argospete

Level 3 Expert

1035 Answers

ykanter

Level 1 Expert

15 Answers

Are you a Medical Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...