Question about The Office Equipment & Supplies

1 Answer

Is there a card counter on the badgy ribbon roll? i used an old used empty roll that was 0% to put a new ribbon on and it comes up as 0% even after rewinding it to the beginning?

Badgy 200 card counter printing or does the ribbon roll have a card counter that restricts the reuse of ribbon rolls?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 691 Answers

Laser printers have small PCBs that count prints and tell you that the toner is empty based on count and not toner level. This may be the same

Posted on Sep 06, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
itdude4321
  • 13 Answers

SOURCE: TAKE UP RIBBON

I work with Zebra printers daily and I have found several ways to enable a stuborn ribbon motor. The S300 is the hardest to turn on but unless the belt has broken or come off it can be done. The S400 and S600 are much easier, below are a couple step that work for me.

Enabling/Disabling the Ribbon motor

Turn off the printer.
Disabling the motor – Press the FEED, CANCEL and MODE buttons while turning the printer on. Continue to hold the buttons until the lower two lights go out.
Enabling the motor – Open the printhead and retract the ribbon completely onto the supply spool. Leave the printhead open. Press the PAUSE, FEED and CANCEL buttons while turning the printer on. Continue to hold the buttons until the lower two lights go out. When the printhead light begins to blink, reinstall the ribbon and close the printhead.
The printer may or may not print out a ribbon sensor profile, this is normal. Cycle the power and you should be good to go.

Posted on Mar 30, 2008

  • 85 Answers

SOURCE: MY SONY UP-10L SNAPLAB PRINTER GIVES ME THE

Hi

This sounds like the sensors are damaged. Best taking to a computer repair centre to be checked out as sony parts can be hard to acquire.

Thanks

Taz

Posted on Oct 23, 2009

  • 6 Answers

SOURCE: DTC550 Fargo printer it says out of ribbon with new installed

Check to see if the RFID (green ring) from the old ribbon has come off and is stuck near the reader (located behind the green stem). I've seen that happen. I've also see some bad RFID rings. If that happens they should have a warranty from Fargo.
onlineidtech

Posted on Apr 06, 2010

  • 55 Answers

SOURCE: My Canon AE-1 Program will not rewind. I shot the

I think you have already ruined the film except the frames that are rewind back to the film cartridge.
You can take the film out from the camera, push in the rewind button at the bottom, pull out the film from the film take up reel.
On the film cartridge, turn on the long tube in the middle clockwise to wind all the film back into the cartridge.
If you had the back opened briefly, do manual film rewinding in the dark room.

Posted on Jun 17, 2010

ozztech
  • 285 Answers

SOURCE: Zebra P330i Printer not counting the YMCKO ribbon correctly

!RIBLEN - - - - Get number of remaining panels on ribbon
Send the command !CSA_0
Send the command !CSA_1

Posted on Nov 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I choose Find a Picture t is telling me the values are wrong.


You should contact your local reseller. I'm sorry, Badgy is not sold outside U.S., so I don't know the printer.

Sep 17, 2014 | Evolis Badgy BDG101FRU Card Printer. BADGY...

1 Answer

Evolis badgy cannot print


See http://www.badgy.com/en/support-troubleshooting.php

May 05, 2012 | Evolis Badgy BDG101FRU Card Printer

2 Answers

Ribbon feeds out with label


Your take up spool isn't working properly, bad motor or belt.

Oct 15, 2010 | Intermec EasyCoder PM4i Printer

1 Answer

DTC550 Fargo printer it says out of ribbon with new installed


Check to see if the RFID (green ring) from the old ribbon has come off and is stuck near the reader (located behind the green stem). I've seen that happen. I've also see some bad RFID rings. If that happens they should have a warranty from Fargo.
onlineidtech

Mar 19, 2010 | Fargo DTC550 Thermal Card Printer

1 Answer

Datacard sp55 printer won't recognize ribbon


PR-01726 Ribbon Out
Out of print ribbon.
Possible Cause 1 : The print ribbon Cartridge is empty.

Solution 1 : Reload the print cartridge. Change the cleaning sleeve and replace the cartridge in the printer. Run a cleaning card as soon as printing is completed.

Possible Cause 2 : The printer ribbon is not loaded correctly.
Soultion 2 :Load the printer ribbon correctly and then close the cover.

Possible Cause 3 : This ribbon has been completely used.
Solution 3 : Use a new roll of ribbon.

Tips for Success
* When this message appears, replace the old ribbon with the new ribbon of the same type. The printer has already prepared the card data for this ribbon type. You can change the colors of monochrome ribbon (such as from dark blue to gold).

* If you must change the type of ribbon (such as (YMCKT to KT) when this message appears, install the new ribbon, cancel any cards waiting to print, and change the ribbon type settings. Finally, return to the card creation program to send the card data to print.

* If the ribbon was repaired, the wrong take-up spool was used. Repair the ribbon again, using the correct take-up spool.

If you cannot fix the problem contact your service provider for assistance.

FTB

Nov 23, 2009 | Datacard Group SP55 Card Printer

2 Answers

Error code 754


It's very possible you are not installing the ribbon properly.
When loading a new ribbon on a Monarch printer, you must save the plastic ribbon core (it's butter yellow in color) from the previous roll of ribbon. The core is what the ribbon is wound up on.
Do not throw away this plastic core - you need it for the next roll of ribbon you load!
You have to move this now empty core from the back ribbon spindle and slide it on the front ribbon spindle. You then load the new ribbon on the back spindle and attach the ribbon end to the empty plastic ribbon core on the front spindle.
You CAN NOT just tape the ribbon to the front spindle. You must have an empty ribbon core to attach the new ribbon to. The printer will give a 754 error unless you have two plastic cores on the two spindles. It can also give a 754 error if the ribbon is not loaded properly, and also if you have a bad motherboard. There are no ribbon sensors, so that's never going to be a problem...

Jul 28, 2008 | Paxar Monarch 9850 Thermal Printer

2 Answers

Ribbon empty


Winding technique:
To wind a new ribbon, take the cartridge housing apart and remove the old ribbon and two cardboard cores. The new ribbon is fitted with the larger roll (the ink ribbon supply spool) at the rear side of the cartridge (as the housing is viewed when it is normally installed into the machine). The ribbon winds over the topside of the rear spool (the supply side) and feeds into the underside of the front spool (the take-up side). Make sure the ribbon is wound neatly, evenly and is tight. If the ink film has become detached or is too loose on the front spool it will not wind on and cause a machine error. If required, use a small amount of sticky tape to secure the ink film to the front cardboard spool and then neatly wind it on to the take-up spool a minimum of five turns, making sure the film does not overhang at the edges. Now reassemble the housing and refit into the machine.
If it’s still not fixed:
If problems persist after fitting a new ribbon, try replacing the entire ink ribbon unit (cartridge housing + a new ink ribbon) using a new, genuine Brother unit before requesting a service; this will be less expensive as the actual housing may have been damaged and is causing the problem and this unit is readily available as a consumable item through sales outlets. If the machine still has problems, book your machine in to be repaired with an authorised Brother Service Centre.

Feb 17, 2008 | Brother FAX-575 Plain Paper Thermal

1 Answer

The printer say there is no ribon but i put a new one and still it's not working


try to install again but this time make sure you follow the manual especially on step 5,6 and 7 I list down again the step from the manual 5: Load the new roll of print ribbon on the cartridge. ? Put the full spool of ribbon on the supply spindle of the ribbon cartridge. Push until the spool clicks onto the spindle. ? Put the empty take-up spool on the spindle with the solid black gear. Push until the spool clicks onto the spindle. 6: Replace the loaded ribbon cartridge in the printer. ? Make sure both spindles rest in the black supports on the left side of the printer. ? Make sure the ribbon cartridge handle rests in the supports on the right side of the printer. ? Make sure to install the full, new spool toward the card tray of the printer. 7 Close the printer cover. Press down firmly to latch it.

Aug 30, 2007 | Datacard SP35 Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top The Office Equipment & Supplies Experts

Scott Yeoman

Level 2 Expert

121 Answers

vince

Level 3 Expert

1234 Answers

Are you a The Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...