Question about U-Line 75WC Wine Cooler

1 Answer

Replaced control on u-line 75WC wine cooler now runs constantly

I attempted to bed the sensor in the same spot of the liner where I had removed the old one and am wondering if I did not "bed" it deep enough?
The unit is now running constantly at the lowest setting on the control and is too cold...
Any ideas?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 286 Answers

If the sensor of the thermostat is not on the evaporator plate then yes the thermostat will never be satisfied. Because it is not reading air temp only the evaporator plates temp. should be clamped onto the bottom of plate.

Posted on Sep 14, 2009

Testimonial: "Going to check and thanks for the response. I am 99% sure this is the probelm!"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Repair Berliner


Many different bed liners exist, made out of many materials of many thicknesses. I am not clairvoyant so I cannot tell which bed liner you have in your truck.
Whatever bed liner you have, the fact t hat it has a small tear only underlines the fact that it has done its job by protecting the paint in the bed of your truck. Repairs or replacement of the bedliner seems a relatively minor consideration, and should be a fairly simple procedure (depending on WHAT KIND of bed liner you have).

May 17, 2015 | 2007 Dodge Ram Truck

Tip

Vinyl tops for cars, LOOKS GREAT PLUS IT'S INEXPENSIVE!!!


Are you restoring a cars vinyl top? It is VERY costly to have one replaced, upwards of $1500. Here's how to do it for a song! Remove the old vinyl top by scraping and cutting. Remove the window trim if necessary. Prepare the surface of the cars top by sanding as if you were going to paint it. You don't need to primer paint it. Go to your local parts store and by a spray on truck bed liner kit. Some can be bought for as little as $99. Mask and protect all areas of the car you don't want to be covered with liner. Apply the liner to the top just as per directions on the kit, as if you were applying it to a truck bed. Allow to dry thoroughly. The result is a beautiful 'Vinyl' looking top that is almost bullet proof and will last ten times longer than vinyl. Cost; about $150 and an afternoon. I used this method on a 1978 Ford LTD II I restored. It took 2nd place in a car show! I listed this under Ford cars, but it works on all cars! Good luck! You're gonna' LOVE the results!-- 8-)
This Tip offered by Bruce Beaven 5-30-2010

on May 30, 2010 | Ford LTD Cars & Trucks

1 Answer

I remove everything and clean it but still say paper jam2 what is the 2 stand for


I switched on and off the machine. While the machine is running and the rollers are turning. I put a photo paper (which is thicker than normally paper on the manul feed section and make sure is far deep enough for the machine to run the paper in. Once the photo papert come out from the machine. The false paper jam 2 signal is re-set. I notice that there is a tiny black spot on the my blank photo paper. I guess, the black spot on the sensor created the false sensor effect as a paper there. Once the black spot was clear by the photo paper. It removed the false sensor and the machine back to normal state. I am very happy with the outcome.

Apr 11, 2012 | Samsung SCX 4521F All-In-One Laser Printer

1 Answer

Uline 75WC Wine cooler: light works but fan and compressor do not come on. Wire cnnections are fine.


Does the compressor vibrabte? If not, the PCB isn't working and should be replaced or worst case is your compressor burned out.

Jan 22, 2012 | U-Line 75WC Wine Cooler

1 Answer

We have a new drilled well which still has orange mud in the filter after a month. The well driller now says it needs a liner for another $2500. Will this solve the problem?


Your asking a question that a geologist should answer but.... I will comment below.

There are a lot of variables that are unknown here. Is this a deep well or a shallow well?
Orange mud after a month hmmm.. It makes one wonder if they have the foot / check valve shoved into the mud? Has anyone tried shortening the pick-up line say 2 feet just to make sure the foot valve isn't in the mud? A couple of other experiences is to unhook the house plumbing and overboard the water until the well runs temporarily dry and visually inspect the well cavity for cave- ins. If there are no cave ins.... I would have my doubts on the liner fixing anything.

If it is a deep well obviously you can not visually inspect anything deep. BUT... you can overboard the water straight from the pump outlet. Most wells will clear up if you overboard water daily for 7 to 10 days until the pump stops pumping. If the foot valve is in the mud it may take many months to stop having orange mud in the filter. Unless your well is in some pretty soft dirt I do not think liner would be required... how ever... if you raise the foot valve 2 feed and still have orange muddy filters... you may have to go for the liner.

I would say the liner is the fix of last resort.
Plan of action:
1. Overboard water daily until the pump stops pumping. You may have to re-prime the pump but, if you wait 45 mins after shutting the pump off the water level should recover enough you do not have to prime the pump.
2. After 10 days or so of repeated ove- boarding sessions until the pump stops pumping... you still have the muddy orange stuff... RAISE the foot valve 2 feet (Someone may have to cut off the pipe 24 inches and re-thread it)
3. If you have done the above and still have the orange mud in the filter..... DO NOT allow the driller to install the liner without a guarantee. I would also stipulate that if it does not cure the mud issue he is going to pull out the liner and refund the cost for same. ( He will tell you... we can not pull out the liner ) If he knows he might have to pull it out.... He will make sure he can remove it!

Feel free to seek the advice of others. This is a who answered your question:
http://blog.fixya.com/index.php/2010/05/award-winning-service
Being from Iowa and growing up on a farm and having wells drilled I pass along my experience. We also thawed long plumbing runs with welders in the winter time running 150 Amps DC end to end for several hours just so the cattle hydrant lines or home plumbing piping would thaw.

Thanks for choosing FixYa and again no worries if you seek other advice. Sometimes like in this situation... it just might be wise. I passed on what I would do if I were to show up on your door step and attempt to try and solve the orange mud / dirt problem you have.

Kelly

Jul 12, 2011 | Dishwashers

1 Answer

How do you remove the tail light assembly to change bulbs on a 2003 frontier sc.


There are two phillips-headed bolts on each inside corner of the truck bed, behind the tailgate latches, that may be used to attach the brackets for the optional bed extender. If you have a bed liner installed, you will need to pull the corner of the liner back to expose the bolts.The factory bed liner needs to be flexed around the upper cargo hook to gain access to the two hex head screws that hold the tail-light housing against the body.Remove the screws so the tail light housing gets loose and easily comes out. this will help.please keep updated for further assistance if more help required. thanks.

Apr 29, 2010 | 2005 Nissan Frontier

1 Answer

Wine cooler not running. When thermostat was


You have either a week connection or a bad thermostat. Check your connections. Part # 2767-s

Oct 06, 2009 | U-Line 75WC Wine Cooler

1 Answer

Wine fridge thermostat


No pictures, the new one goes in the same as the old one comes out. You have 2 screws on the bottom of the evaporator that holds the sensor in place. Then the sensor runs thru the bottom toward the back.As you remove the old one jus put the new one in the same way.

Oct 02, 2009 | U-Line 75WC Wine Cooler

1 Answer

Gets cold but does not shut off.


Check the thermostat to make sure its mounted on the evaporator plate. If its away then the sensor will never satisfy your control, Or you may need to replace the control

Oct 01, 2009 | U-Line 75WC Wine Cooler

1 Answer

I need to replace the metal racks in the u line 75wc refrigerator. They rusted in the back.


To order the racks you will need to order from a parts distributor. To find one in your location just visit U-line. www.u-line.com and under customer service you will see parts locator.

Sep 26, 2009 | U-Line 75WC Wine Cooler

Not finding what you are looking for?
U-Line 75WC Wine Cooler Logo

Related Topics:

641 people viewed this question

Ask a Question

Usually answered in minutes!

Top U-Line Furniture Experts

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Brad Brown

Level 3 Expert

18108 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

Are you an U-Line Furniture Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...