Question about KitchenAid 32685 Mixer

2 Answers

Will not turn on - KitchenAid 32685 Mixer

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 143 Answers

This can be caused by a number of things. The first thing to check will be the carbon brushes located on the left and right sides of the unit. Just simply unscrew the caps with a straight screwdriver. Once removed your can clearly see the shape of the carbon brushes. If they appear to have little or no wear and aren't broken, this won't be the cause of this problem. Also take note when you take them out AND put them back in as they willl only fit ONE way. The next thing to check will be the main control at the rear of the unit. After removing the power source, you can also remove the rear access panel. A phillips screwdriver is required. Next after removing the panel, you can now see the main board. Inspect it for any immediate signs of broken or burned wires also check the bi-metal on the control itself, as this will often indicate a faulty board. If however, everything looks good visibly and you still have no power to the unit, the last possible solution could be that the power cord itself has an internal problem. Hope this helps

Thanks

Posted on Dec 02, 2009

  • 3 more comments 
  • Matthew Bunn
    Matthew Bunn Mar 03, 2014

    Just a quick amplification. If you have messed with the brushes double check that they replaced correctly. They can fit inside the mixer and still be facing the wrong way. Get a flashlight and check for the little block that holds them in the correct position.

  • Maureen Monaghan
    Maureen Monaghan May 24, 2014

    wow thanks!! I just bought a kitchen aid mixer at Goodwill for $25 because it wasn't working. Hubby re-checked the brushes after I read this post and sure enough the 2nd time it turned on!!

  • Loren Ostroff
    Loren Ostroff Dec 25, 2014

    I cannot believe that just worked! I called KitchenAid and they told me my only option was to take it to an appliance repair shop. All I did was wipe off the carbon pieces and it started working again! Thanks so much.

  • Papi Oso
    Papi Oso Aug 26, 2015

    Another quick check that might help is simply moving the cord around while it's plugged in and turned on ON THE LOWEST SETTING. If it's a break in the cord (especially likely near the plug or mixer end), the movement might re-establish the connection just long enough to bring the mixer to life. This is especially likely if you move your mixer a lot, and wind up the cord to do it. If it does, that's your culprit, and it will save you time, money, and frustration. Now- just because it didn't come on doesn't mean it's NOT the cord- but it's one quick and cheap way to check it.

    Remember Occhem's Razor- "The simplest answer is very often the right one.

  • CRYSTAL G M
    CRYSTAL G M Dec 07, 2018

    Omg...life saver! It was the carbon brushes!

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Electrical parts can appear to be good but can still be bad. They must be tested by somebody qualified in diagnostic procedures of electrical problems.

Most likely the cord won't be the problem unless it's where the cord terminates or the cord flexes during use. Constant flexing will cause wire to break eventually and sometimes even the best assemblers in the world can muss up a terminal connection. This can even pass quality control as they only test if the connection is made (one out of the 22 conductors can be made and it'll pass the QC check and the first load that's put on it will blow the one wire that should have been 22 times as strong) and not if it will handle a load. mind you, it was the fault of the assemblers, not the user.

The individual components such as resistors, capacitors, diodes, transistors, and other things failure rates are actually based on the purity of the components that made them and the cleanliness of the room they were assembled in. For a well designed piece of equipment, you can expect the failures to be because of these reasons. for not so well designed pieces... you get the idea.

Last thing you have to consider is the craftsmanship used in assembling the item. Was it designed and assembled to last forever or was it designed right using correct materials but assembled by somebody that didn't even care if all the parts got in correctly.

Posted on Jan 26, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The paddle on my kitchenaid won't turn. It just makes a humming noise. Any suggestions?


Is the humming noise the sound of the motor straining to turn without moving (it won't last very long like that) or the sound of the motor turning but not operating the paddle?

Dec 21, 2014 | KitchenAid Food Mixers

1 Answer

My D300T motor is turning but shaft is not. How do I open the shaft area.


Weird sound usually means something in the gear box. I found a copy of the manual which includes many exploded drawings; perhaps something in here might help:
http://www.bakedeco.com/ebay/pdf/HobartD300.pdf

Nov 23, 2013 | Hobart D300 Stand Mixer

1 Answer

Kitchenaid rrk5a not operating in lower speed settings


The RR of your model number stands for reconditioned, your actual model number is K5A, I believe that the side trim band says Hobart on the side, if not you may have a new trim band (Generic type) put on during the reconditioning to pretty it up. In any event in the back of the mixer is an end cover, at the top is a small Phillips head screw, remove it and lift the end cover up and slightly out, (because there are two small and fragile clips on the back that can be easily broken off, they help hold the end cover in place so up and out ) once the cover is removed you will see a black and copper plate with three chrome screws on it in an upside down triangle shape, the two top screws are for adjusting speeds from stir to 6, the lower one is for adjusting speeds from 6 to 10, Turn the screw on the top left to the left a quarter turn while the mixer is in the stir position. it should start turning. if not turn the screw on the right a quarter turn, the mixer should start, if not turn back the other way (both top screws a half turn) if it machine does not start then there is a strong possibility that it is the bottom screw, the bottom screw can and sometimes does get turned in or out due to the pressure caused by contact that it makes with the speed control switch bar attached to the side speed control switch, so let's try that one, turn it counterclockwise or clockwise (no more than one full turn) a quarter turn at a time, if it is the bottom center screw causing the problem then it should start within a full turn, try not to turn the screw in either direction more than one full turn as you can really screw up your speed settings. Don't panic I am probably making it sound more difficult than it really is, just remember that a little is a lot. I am a KA tech and every machine that I have worked on that has a low speed not working correctly it has turned out to be these 3 screws.


If your machine goes to high speed from the get go no matter where you put the speed switch, well that is another problem, but if your machine is not working on lower speeds when set to the lower speed and it does work at higher speeds when the switch is set to the higher speeds then it is the 3 adjusting screws on the speed control plate. hope this helps if not let us know

Jan 20, 2013 | KitchenAid Food Mixers

1 Answer

Blade will not turn


motor will hum but no blade turn if bottom seal worn and material leaks into shaft. Rekove drive head and try turning shaft if nio go dissasemble entire unit ,clean and service, replace seals

Sep 20, 2009 | Robot Coupe MP600 750 Watts Hand Mixer

1 Answer

Turntable does not turn. Motor runs. Beaters work.


I have the same one, and the turn table has never turned on it's own. from looking at the bottom of the stand, i think the mixers are supposed to turn the bowl, so i just give it a little turn, and the mixers kinda take care of the rest. BTW, i got 2 sets of beaters with mine and i dont know what the second set is for, do you? contact me at rawemo@hotmail.com

Feb 18, 2009 | Sunbeam Food Mixers

1 Answer

Blade is hitting the bowl and the screw will not turn anymore


Turn the screw to the right. It will only turn a quarter turn. If that doesn't help try to file a bit of metal off the bottom of the beater. If you find this solution helpful, please rate it. ricardok45

Jan 01, 2009 | KitchenAid K5SS Heavy Duty Commercial...

1 Answer

H-600 Turn Handle slips, bowl does not go back down


Does the handle seem to move easier?there is a shear pin on the handle and if it breaks the bowl wont move.Another thing to check is remove the silver plateon the front of the mixer there are 2 possibly 4 screws,when you remove this plate you will see a long screw about 3 feet long.turn the handle if the screw doesnt turn that pin may be broken.let me know.

Mar 18, 2008 | Hobart H600 Stand Mixer

1 Answer

Attachments won't turn


most likely a stripped worm gear if the motor still runs but the attachments/planetary gear won't turn.
Did this happen when mixing a big batch of dough or when something fell in the bowl that shouldn't have?

Dec 16, 2007 | KitchenAid K45SS Classic Stand Mixer

1 Answer

Sunbeam hand mixer. One beater not working


That spring does not turn the beaters. It is part of the beater release assembly. Probably one of the gears is worn.

Nov 12, 2006 | Sunbeam 2485 MixMaster Series Hand Mixer

Not finding what you are looking for?
KitchenAid 32685 Mixer Logo

Related Topics:

34,917 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Food Mixers Experts

Appliance engineer

Level 2 Expert

153 Answers

CJ C
CJ C

Level 2 Expert

66 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a KitchenAid Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...