Question about Lexmark E260dn Laser Printer

2 Answers

How to reset lexmark e260dn on factory defaults

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

1.Turn the printer off.2.Open Front cover.3.Press and hold X button.4.Relese X when the ! LED is illuminated. Note:Be patient as the LEDs will light up in multiple patterns before finaly stopping at !.5.Close front cover. Note:Observe that green button and 3 other LED will be illuminated at the same time.This is Home position.6.Slowly press X button until the 3 first LED are illuminated (paper,toner,light)Note:normaly this will require you to press the X button 11 to 13 times depending on the options and features installed.7. Press and hold green button until all LED flasch or strobe from left to right then relese the button.wait until this process stops with the same pattern as step 6.8.Press and hold X until the light pappern return to the pattern of four LED in the Home position.9.Turn the printer OFF.10.Turn the printer On.Note:if on a DHCP network, wait 30 seconds to see if the DHCP server/router sends out an IP adress to the device.11.Press green button to print a setting pages and observe that all the TCP/IP settings have been reset.12.Reconfigure the device using DHCP.Auto IP(zero configuration) or the IP Setup Utility.
This is my solution to the problem.//Oaklunde

Posted on Jan 06, 2012

  • Nemanja Petrovic
    Nemanja Petrovic Aug 29, 2014

    Hvala meni je ovo uspjelo. Tenx.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 6 Answers

Power off the printer
Remove the network cable
Open the front of the printer
Hold the Continue button
Turn the printer on
After the lights cycle a few times, let go of the Continue button
Close the front of the printer when the yellow light is on, telling you that there is an error (because the front cover is open)
There will be 4 lights that will be on, press the X (cancel) button and it will turn into one light. Hold the continue button down, it will print the Printer Settings Configuration page which will instruct you further.

Posted on Dec 08, 2010

  • Hilal Feb 24, 2011

    If it doesn't work, you'll need to print out a test page to show the ip address, connect it to a hub, access the web page and change the ip address from there.

×

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

JohnGJohn
  • 215 Answers

SOURCE: I would like to know how to reset the Lexmark

Restoring the factory default settings

Do one of the following:
• If your printer is on a network, access the Embedded Web Server:

1 Type the printer IP address into the address field of your Web browser.
Note: If you do not know the IP address of the printer, print a network setup page and locate the IP address in the TCP/IP section.
2 From the Settings screen, click General Settings.
3 Under Factory Defaults, select Restore Now, and then click Submit.

• If your printer is connected to a computer by a USB or parallel cable, use the Local Printer Settings Utility for Windows or Printer Settings for Macintosh.
1 Open the utility.
2 Do one of the following:
– From the Local Printer Settings Utility menu bar, click Actions Restore Factory Defaults.
– From Printer Settings, click Factory Defaults.

Warning—Potential Damage: Restore Factory Defaults returns all printer settings to the factory default settings except Network/Port menu settings. All downloads stored in RAM are deleted. Downloads stored in flash memory or on a printer hard disk are not affected.



Or please download the user guide from this link and follow the instructions
http://static.tigerdirect.ca/pdf/Lexmark-E260D-Series-Mono-Laser-Printer-Manual.pdf

Hope this will help you
thanks

Posted on Oct 01, 2009

  • 1 Answer

SOURCE: I would like to know how to reset the Lexmark

in lexmark e260dn when i connected to lan it is not getting ip

Posted on May 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, my lexmark e260dn "load paper" light stays on even though paper is loaded. please help


Please check if the paper guides on the paper tray are correctly positioned. For example, if you are using a letter sized paper, make sure the guides are set to 8"x11".

Dec 20, 2012 | Lexmark E260dn Laser Printer

1 Answer

How to reset photoconductor counter on Lexmark E260dn


Please click on the link below, this will show you how to reset the photoconductor counter. http://bitly.com/rh8ZSV

If you need further assistance please contact Lexmark Technical Support.


Oct 16, 2011 | Lexmark E260dn Laser Printer

1 Answer

How do you reset the photoconductor counter on the lexmark e260dn? the light is blinking yellow right after i replaced the toner cartridge. Have put this printer through a lot of use over the last 3/4 of...


1.open the front cover. Leave the printer powered on. 2. With the front cover open, press and hold the stop/cancel (X) button. 3. Eventually all of the lights will begin flashing, indicating that the photoconductor page count has reset. When you see this light sequence, let go of the X button.
4. Close the front cover.
NOTE: If you wish to confirm that the photoconductor page count has reset, print a menu settings page.

Jul 09, 2011 | Lexmark E260dn Laser Printer

1 Answer

Reset printer


Please print printer settings configuration page. The page will explain the printer menus and change values. Menus are represented by Continue, Ready/Data, Toner Low and Load/Remove Paper light sequences. Menu Items and their values are indicated by Paper Jam and Error Light sequences

Here are the instructions to do that:

1. Turn off the printer.

2. Open the front access cover

3. Press and hold the red Stop button while powering up the printer.

4. The lights should cycle, release it when the light stops cycling.

5. Close the cover once the ! light displays

6. The lights should cycle again.

7. Then press the Continue button.

8. This should print a Printer Diagnostics page.

9. On the Printer diagnostic page, Use the Utilities menu to troubleshoot printer problems

- Return the printer settings to factory default values.

- Sometimes resetting the printer to the original settings solves formatting problems.

- All menu items are reset to the factory default values except:

- All settings in the Parallel menu, Network menu, and USB menu.

- All downloaded resources (fonts, macros, and symbol sets) in printer memory (RAM) are deleted.

- Resources in flash memory are unaffected.

10. Please locate the value that would say "Factory Defaults".

11. We would need to follow the exact light sequence that you see for the "Factory Defaults".

12. Press and release the Cancel button to advance through the menus and the menu items to the one we would need.

13. Press and hold the Continue button until all the lights cycle to save the function/value.

14. Restart the printer.

Jun 16, 2011 | Lexmark E260dn Laser Printer

1 Answer

My lexmark printer x4875 only copies part of the page


Try to reset your printer to factory default settings. Go to Maintenance -> hit check -> select Reset Defaults -> select first option only to reset factory defaults. Try to make a copy again.

Apr 11, 2011 | Lexmark X4875 InkJet Printer

1 Answer

A impressora lexmark e260dn não


O cartucho de toner pode estar ficando com pouco toner:

? Remova o cartucho de toner eo cartucho de toner.

? Shake it dum lado ao outro para redistribuir o toner.

? Reinstale-o e verifique novamente para a condi??o.


Para obter mais assist?ncia, entre em contato com o Suporte T?cnico da Lexmark

Jan 20, 2011 | Lexmark E260dn Laser Printer

2 Answers

I would like to know how to reset the Lexmark E260dn to factory defaults. The printer was set with a static IP address and no longer exists on THAT network. I need to set it up as a DHCP client again to...


Restoring the factory default settings

Do one of the following:
• If your printer is on a network, access the Embedded Web Server:

1 Type the printer IP address into the address field of your Web browser.
Note: If you do not know the IP address of the printer, print a network setup page and locate the IP address in the TCP/IP section.
2 From the Settings screen, click General Settings.
3 Under Factory Defaults, select Restore Now, and then click Submit.

• If your printer is connected to a computer by a USB or parallel cable, use the Local Printer Settings Utility for Windows or Printer Settings for Macintosh.
1 Open the utility.
2 Do one of the following:
– From the Local Printer Settings Utility menu bar, click Actions Restore Factory Defaults.
– From Printer Settings, click Factory Defaults.

Warning—Potential Damage: Restore Factory Defaults returns all printer settings to the factory default settings except Network/Port menu settings. All downloads stored in RAM are deleted. Downloads stored in flash memory or on a printer hard disk are not affected.



Or please download the user guide from this link and follow the instructions
http://static.tigerdirect.ca/pdf/Lexmark-E260D-Series-Mono-Laser-Printer-Manual.pdf

Hope this will help you
thanks

Oct 01, 2009 | Lexmark E260dn Laser Printer

Not finding what you are looking for?
Lexmark E260dn Laser Printer Logo

37,579 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexmark Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Are you a Lexmark Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...