Question about HP LaserJet P3005n Printer

1 Answer

HP LaserJet P3005 printer prints wrinkled paper

I have an HP LaserJet P3005 printer that prints wrinkled pages. I already checked for debri that might be blocking the rolls thus wrinkling the paper. What could be causing the paper to come out wrinkled?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

2 reasons:
1. Was there a paper jam prior to this problem? It could be that the paper was pulled out and a small bit of it is stuck on the pins that guide the paper from the heat roller. If no torn jammed paper prior to this issue, then check out 2.

2. the heater/roller is damaged and needs to be replaced. I would suggest you take it to your nearest HP dealer to properly diagnose this for you.This would save you unnecessary cost in trying to pull it apart and causing more damage to it.

Good Luck,

Posted on Jan 29, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HP laserjet p3005 it was working ok as we don=ont change the settings often. From yesterday, as soon as we give a print command, it gives a message "LOAD TRAY 1 LIGHT LETTER, then when we press green...


This is a settings problem, you will need to go through the paper handling menu on the printer and on your computer to ensure they are set to the correct paper size that you are trying to print on.

Aug 10, 2011 | HP LaserJet P3005 Printer

1 Answer

Paper is wrinkled on one side


Hewlett Packard P3005 Fuser


The HP P3005 fuser is located at the back of the printer.


The fuser has a thin film upper roller which can be torn, some symptons can be "Wrinkled Pages","Poor Fusing", "Toner Rubs Off the Page", "Pieces of black Plastic Come Out".


*** The printer should be unplugged from any power source before any servicing is performed ***


The rear cover can be taken off by removing 2 screws. Once the cover has been removed the fuser can be removed by taking out 4 screws and 3 electrical connections.


Part Number and purchasing link below


RM1-3717-020

Jan 16, 2011 | HP LaserJet P3005 Printer

1 Answer

My HP Laserjet P3005 is almost 2 years old and needs a new fuser assembly. Is this normal? How much should this cost? Would I be better off buying a new printer


Hewlett Packard P3005 Fuser


The HP P3005 fuser is located at the back of the printer.


The fuser is suppose to last up to 200,000 pages, however they rarely get that far.


The fuser has a thin film upper roller which can be torn, some symptons can be "Wrinkled Pages","Poor Fusing", "Toner Rubs Off the Page", "Pieces of black Plastic Come Out".


*** The printer should be unplugged from any power source before any servicing is performed ***


The rear cover can be taken off by removing 2 screws. Once the cover has been removed the fuser can be removed by taking out 4 screws and 3 electrical connections.


Part Number and purchasing link below


RM1-3717-020

Dec 07, 2010 | HP LaserJet P3005 Printer

1 Answer

LJ P3005, will not print from tray 2. Tray 2 is


Do a factory reset then reconfigure device one more time.

Jan 24, 2018 | HP LaserJet P3005n Printer

1 Answer

HP P3005 - skid marks along paper's edge


Print 3 pages. Use the manual feed tray. As they print, open the cover, remove the toner and look down at the paper in the printer. Do you see marks along the edge? If no...replace the fuser. If yes...it could be the transfer roller.

Jan 07, 2010 | HP P3005d Monochrome LaserJet Printer

1 Answer

Paper printing with wrinkles on hp 4100 laser


Pressure roller is worn. But the whole fuser assembly could probably stand to be replaced.

Mar 28, 2009 | HP LaserJet 4100n Printer

1 Answer

CLJ8550n poor print quality and wrinkled paper


this is usually not caused by the paper tray. this problem is usually caused by the fuser assembly. check your paper path. dead cycle the printer, shut the printer down before the paper enters the fusing area, check for wrinkles. remove all paper, print again, check the output, wrinkles, replace the fuser.

Feb 03, 2009 | HP Color LaserJet 8550n Printer

Not finding what you are looking for?
HP LaserJet P3005n Printer Logo

2,638 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...