Question about Samsung DMR57LFS Stainless Steel Builtin Dishwasher

1 Answer

No power showing on display board, checked electrical hookups it ok. Outlet has power. checked child tamper and delay no response

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 8 Answers

Its the fuse, its located under the dishwasher. take off the bottom white plate, its on the right side of the pump on a wire harness. Its in a fuse cartridge turn to the left take out fuse and replace with 15 amp fuse take it radio shack and have it matched.

Posted on May 06, 2010

  • lbwf Aug 30, 2011

    THANK YOU! This was an easy repair thanks to your post. The only trouble I had was getting the black cartridge open to take out the fuse. We purchased all Samsung appliances for our kitchen two years ago, and I have not been happy with the problems they've caused. Thanks again, I hope the repair lasts for a decent amount of time. Lori

  • Amanda Green
    Amanda Green Feb 20, 2014

    Does the dishwasher have to be pulled out to access the fuse?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Door not unlocking Fisher Paykel front loader Wh60f60w. The cycle appears to have completed but the door remains locked well beyond normal lock delay. Is there a manual release?


Have switched this on?

Child-proof lock
? You can protect the appliance from being tampered by activating the child-proof lock.
? When activated, no change can be made to the programme running.
To activate the child-proof lock:
1 Press the 1st and 2nd additional function buttons for 3 seconds.
2 The "C ON" (child lock is activated) symbol appears on the screen.
Note: the child lock symbol will also be displayed whenever any button is pressed while the
machine is child-locked.
3 The child-proof lock lamp on the programme follow-up indicator will light up when the childproof lock is activated.
To deactivate the child-proof lock:
1 Press the 1st and 2nd additional function buttons for 3 seconds.
2 The "C OFF" (child-proof lock is deactivated) symbol appears on the screen.
3 The child-proof lock lamp on the programme follow-up indicator will go off when the child-proof
lock is deactivated.

Apr 01, 2017 | Fisher Washing Machines

1 Answer

Bad display panel


Might be. http://electronicshelponline.blogspot.com/. Check this link for more detail troubleshooting to Plasma displays, and make it sure.

Jun 13, 2013 | Samsung PN51D550C1F 3D Plasma TV

1 Answer

MIne Whirlpool duet is having probloms please help me with it!


see this causes and fix it. God bless you
User Control and Display Board If the washer won't start, the user control and display board may be defective. Check for power to the washer first.

Timer If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

Line Fuse If the washer won't start the line fuse might have blown.

Thermal Fuse If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.

Line Fuse and Holder If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.

Main Control Board If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.

Door or Lid Latch Assembly If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.

Door Lock Motor and Switch Assembly If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.

Incoming Power Problem If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the home.

Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.


10_5_2012_7_02_41_pm.gif

Oct 05, 2012 | Indesit W 123 Front Load Washer

1 Answer

When you push start button nothing happens


see this causes and fix it. God bless you
User Control and Display Board If the washer won't start, the user control and display board may be defective. Check for power to the washer first.

Timer If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

Line Fuse If the washer won't start the line fuse might have blown.
Thermal Fuse If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.

Line Fuse and Holder If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.

Main Control Board If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.

Door or Lid Latch Assembly If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.
Door Lock Motor and Switch Assembly If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.

Incoming Power Problem If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the home.

Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.

9_29_2012_11_52_17_am.gif

Sep 28, 2012 | Washing Machines

1 Answer

No sound from my ja 687 amp lights show receiver is working


Need to check on the power supply to the output drivers, if there is no response on the speakers it is possible that the output replay is under protection. You need to remove power plug and leave aside for an hour before the amplifier is plugged back. If all functions show on display but there is no sound check the PREAMP output- audio out. If there is audio then the fault is with a non switching of the power amp or a power amp protection. Since these are mounted boards with little access to testing you need to be skilled to go further to probe and proceed. Also Denon might refuse to service if the amp is tampered which also can be expensive.

Oct 25, 2011 | Denon AVR-687

1 Answer

My Samsung DMR77LHS dishwasher has NO power showing on display board, checked electrical hookups it ok. Outlet has power. Pressed Power On/off button, no response, all lights are off...


hti had athe same problem, and the fuse fixed it. it turns on now,

you can get to the fuse casing, small tube about 1.5 inches , black, by flowing the electrical line to the, inside , or the under carriage, on the side of the bottom of the unit.
15 amp 250 volt at radio shack.

Sep 12, 2010 | Samsung DMR77LHS Tall Tub Dishwasher

1 Answer

I am installing a Leviton combo switch and tamper resistant outlet. The outlet appears to have plastic behind the holes. What do I do?


Just plug in an appliance. Equal pressure from _both_ of the prongs of the appliance opens the plastic plates. Inserting a _single_ object into a _single_ slot (such as what a child may try to do with a metal object) will not allow the plastic plates to open.
That's the criteria for an outlet to be considered tamper proof anyway.

Aug 04, 2010 | Leviton 15a 120v Sp Switch

1 Answer

Treadmill has no electrical response at all...check the outlet and power strip...nothing...any ideas


I suggest checking your power plug then check or reset the circuit breaker on the treadmill next to the cord if that ok and the unit is still dead. Unplug unit the remove motor shroud and if you own a multi meter plug the unit in and start checking the AC all the way to the lower board and see where the AC is missing.
If the Voltage is good to the board then check DC Out put going the console wire harness should have 5v or 12v DC depending on model if missing then replace lower board if present, then check the continuity of wire harness if bad replace harness. If good upper console needs to be replaced

May 20, 2010 | Proform Sport 1000 Folding Treadmill...

5 Answers

Verifone vx 510 bad rtc chip please reboot


verefone the terminal has a problem in the display shows bad rtc chip, as I can compose for it functioning properly again?

Jan 11, 2010 | VeriFone VX510

1 Answer

Oven Control not working


Vahid, is the display black, nothing there? Try pressing the bake and broil pads together for 3 seconds until display shows SF. Then press clock. If this doesn't work try the ERC test by doing this; Kill the power to the range for 10 seconds. Press the cooking time, delay start and number 8 pads all together. The display should show the word test. Give this a shot first....Catriver..post back.

Nov 12, 2006 | GE Profile Spectra JGBP79 Gas Kitchen...

Not finding what you are looking for?
Samsung DMR57LFS Stainless Steel Builtin Dishwasher Logo

Related Topics:

2,565 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Dishwashers Experts

vince

Level 3 Expert

1234 Answers

gbob59

Level 3 Expert

3042 Answers

Cindy Wells

Level 3 Expert

5964 Answers

Are you a Samsung Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...