Question about Uniden DECT 6.0 Cordless Telephone Expansion Handset

3 Answers

Uniden dect6.0 handsets do not operate

I have two sets of dect 6/0 and none of the handsets get dial tone from base even when plugged in next to bases. what am I doing wrong???

Posted by on

  • 1 more comment 
  • fixbill007 Apr 11, 2008

    I attempt this process but my phone returns "Not Registered." The manual says to repeat the process for this error and I do but get the same result. Help.

  • Anonymous Apr 30, 2008

    exact same problem

  • Anonymous Dec 03, 2008

    Just purchased ours, they ****!

    I will be returning and never purchase another.

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I am writing for my Mum, who is 99. We live far apart, so it is a bit difficult to fix her problem. She had a new Uniden DECT 60 (?) installed in early July. It seemed to be working fine when we left her, but she says it only rings twice before going to voice mail. She says it has always been like that. How can we fix this for her even though we live at a distance?.

Posted on Aug 17, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have lost the pin code of a Samsung SP-R5210 and therefore i canot register it at the base

Posted on Jan 06, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 405 Answers

Sounds like the handsets lost their link to the base. Did you have a power outage recently? Power outages can cause this problem. So you need to register the handsets to the base. Follow this link http://www.uniden.com/index/manuals_results.cfm?cat=59

and select your model # from the list, this is from pg 27 of a dect6.0 1060 model
Registering a new handset
When you register a new handset to your base,
you will be asked to enter the base PIN code.
The pre-set PIN code is 0000. If you wish you can
change this code, see page 29.
Before registering, make sure the new handset is
fully charged and that you have the base and
handset in front of you. Also, make sure all
handsets and the base are in standby.
On the handset you want to register:
1 Press to access the main menu.
2 Press or until Add.settings is
displayed and press .
3 Press or to display Register and
press .
4 Press or to select your base
number and press .
On your base:
5 Press and hold for approx. 3

Hope this helps

Posted on Mar 12, 2008

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

At&t dect 6.0 all 4 handsets say no line


check base unit .
Check phone line is plugged into base and wall
Check base unit has power going to it
If it all looks ok try plugging a normal landline phone into the base unit locations phone line to see if there is dial tone .

Jan 28, 2017 | AT&T Lands Phones

1 Answer

HandsetS #2 and #3 work properly. Handset #1 has a display screen with correct datet and time -- but no dial tone, How can I fix this?


This sounds like Handset #1 has lost its "registration" with
the base. De-registering & re-registering is often easy.

First, be sure the handset battery is well charged as a
weak battery will interfere with the registration process.
Then try this ( 'works for the D1680, D1481, & similar):

To deregister the handset:

1. Press and hold the [END] and [ # ] keys at the same time,
after a few seconds the display will say
"System Reset, Deregister Handset"
press [SELECT]
scroll to "Base Unavailable"
press [SELECT] (chirps) press [END]
display reads "Place in base..."

Next, to re-register the handset:

2. Set the handset into the base cradle and wait,
within ~30 seconds the handset should display
a "Handset #" and be good to go.

Good luck!
--------------

Nov 26, 2015 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

Won't hold a dial tone go new batteries still a problem


Maybe trying to pair the handset with the base station will solve your problem. Look in the manual how the pairing procedure is done for your phone.

If the pairing procedure is done, and the handset finds the base station and there's stil no dial tone, check if the cable from the telephone line is plugged in the base station of the phone and check if the other side of the cable is plugged in the wall phone outlet.

I hope this will solve your problem.

Feb 13, 2014 | Vtech DECT 6.0 Cordless Phone with Digital...

1 Answer

Uniden phone stuck at searching, not getting a dial tone


One thing to try is deregestering your phone and registering it with the base again.

Hole the # and 'End' key on the handset until the next menu appears (about 5 seconds). Select deregister phone (use the 'Menu' button). Do it again, but select "base unavailable". After that, set them in the base (not the handset charger) and they should register with the base.

This works on most Uniden model phones.

Jan 29, 2013 | Uniden DECT 6.0 Cordless Telephone...

1 Answer

We have a DECT 6 system with a base unit and five satellites. Suddenly the satellite phones don't work, but they are alive (with no dial tone and don't ring) and show a message "out of...


Hello.

From FixYa Support:

- unplug base unit for 15 seconds
- press "PROGRAM" button on handset
- from menu, select "HANDSET SETUP"
- from menu, select "REGISTRATION"
- handset display will prompt you to press and hold PAGE button on base unit for 5 seconds, then press "PROGRAM" button on handset

Perform steps for each handset. You may need to plug base unit and unplug for each handset.

Hope this helps.

Jul 27, 2011 | Uniden Cell Phones

1 Answer

On one of the 3 phones I get no dial tone and the message "Unable to Call Try Again"


Re-Register a Handset to the Base
1. Remove Handset Battery.
2. Reconnect battery while holding down "*" and "#" key.
3. Then press the right upper key under the LCD.
4. Press the "End" key.
5. Wait a few seconds and then the phone will be ready to register to the base.
6. Set the phone on the desired base when the phone's display says to.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

Mar 06, 2011 | AT&T DECT 6.0 Cordless Phone System with...

1 Answer

No dial tone. Base will ring. Handset has no


Check the Battery on the Handset. remove the pwr frm the base unit n connect aft 30 sec. aft this if it still says the same msg, then the handset needs to be replaced.


Mar 03, 2010 | Vtech DECT 6.0 Cordless Phone with Digital...

Not finding what you are looking for?
Uniden DECT 6.0 Cordless Telephone Expansion Handset Logo

1,144 people viewed this question

Ask a Question

Usually answered in minutes!

Top Uniden Lands Phones Experts

k24674

Level 3 Expert

8081 Answers

Cindy Wells

Level 3 Expert

6046 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Are you an Uniden Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...