Question about General Electric Adora GHDA670N Built-in Dishwasher

Open Question

GE GHDA696P push in normal wash & heat dry push start. the water starts machine runs for a few mins then all the lights go out. I shut off breaker and turned back on light blink I push start then everything goes blank again.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Red blinking light over normal wash

I had the same problem... the lock on light was blinking continuously. The solution required disassembling the door to get to the control panel electronic board. You'll notice a flat transparent cable coming out of one end, twisting under the board and going into the door panel. In the middle of the door, there's a number of wires taped together that curled over the flat cable. Look for any black tape residue on the flat cable, which seemed to be causing a short circuit and confusing the electronics. After carefully removing the tape residue from the flat cable, the problem went away.
Hope this helps :)

Posted on Apr 03, 2008

Ad
  • 97 Answers

SOURCE: NORMAL Wash light is blinking and I can't CANCEL

turn unit off at the breaker box. let sit for 5mins and turn back on. will usually reset board. be sure door is closing completly. could be a door switch.

Posted on Jun 09, 2009

  • 1 Answer

SOURCE: Kenmore 665 dishwasher blinking clean light

you'll need to enter a diagnostic mode, press in this order, hi-temp(sani-rinse)----heated dry--hitemp---heated dry... all lights should light, close door and let cycle for about a min, after press the cancelbutton, you should be good to go, the buttons on your model may read slighty different names, if this "toggle of buttons" does not work, you can remove thelower access panel and htere willl be a tech sheet/trouble shoooter behind the panel, in there it will explain how to enter diag/test mode

Posted on Jul 02, 2009

RED92JEEPER
  • 51 Answers

SOURCE: Kenmore Ultra Wash Dishwasher - no lights, won't reset

check wire nuts that were used to install power cord/it is on the right hand side of toe kick if ok there is a fuse on the control that you can replace located top of door

Posted on Sep 27, 2009

  • 127 Answers

SOURCE: kenmore dishwasher ultra was quiet guard 3 model

that would be model # 66516012403 correct??
you may have inadvertently set the lock on function..
check this out from your manual...

Lock On
Use the Lock On to prevent unintended use of the dishwasher
between cycles. You can also use the lock feature to prevent
unintended cycle or option changes during a cycle.
When LOCK ON is lit, all buttons are disabled.
NOTE: The dishwasher door can be opened while the controls
are locked. However, the lock must be turned off and the Start/
Resume button pressed to resume the cycle.
To turn on the Lock
Press and hold HEATED DRY for 4 seconds. LOCK ON glows.
If you press any pad while your dishwasher is locked, the light
flashes 3 times.
NOTE: If the Heated Dry option is selected, the light will
temporarily turn off until Lock On glows.
To turn off the Lock
Press and hold HEATED DRY for 4 seconds. The light turns off.

hope this helps,
best of luck,
ttfn

Posted on Oct 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is heated dry blinking?


FIXED Kenmore dishwasher lights flashing: "Hi Temp" & "Heat Dry ...

www.applianceblog.com/.../40588-Kenmore-dishwasher-lights-flashing-...

Aug 26, 2013 - 10 posts - ‎3 authors
Thread: Kenmore dishwasher lights flashing: "Hi Temp" & "Heat Dry" ... A few months ago, we had a brief power outage and the next morning, noticed the "Hi Temp" and "Heat Dry" lights were flashing. ... Well since then, the dishwasher intermittently stops mid-cycle and these same lights ... Thread: GE Eterna QuietPower 2 Normal and Heated Dry ...
6 posts
Feb 24, 2012
Kenmore Elist 665 dishwasher Smart Wash red light ...
6 posts
Dec 23, 2011
Heated dry blinking +17 times - ApplianceBlog
10 posts
Nov 14, 2010
Heated Dry light blinking
3 posts
Nov 7, 2010
More results from www.applianceblog.com

Why won't my dishwasher start and why does the "Heated Dry"

www.shopyourway.com > Manage My Life > Questions
Nov 16, 2009 - When I hold down the Heated Dry button to turn the control lock on it ...my dishwasher start and why does the "Heated Dry" light keep blinking ...

Dec 01, 2015 | Dishwashers

1 Answer

How do I reset the code.the lights are lit 4 hour delay, rinse only steam clean.


THIS DISHWASHER WAS RECALLED BY MAYTAG.. You might want to call them to see if it is still covered.
If already repaired you might try:
Normal - heated dry - normal - heated dry. then try to use the machine.

Oct 19, 2015 | Maytag MDB7809AWB - MaytagR JetcleanR Plus...

1 Answer

The clean light keeps blinking and the dishwasher will not start. I pushed the cancel button and it runs for about 30 seconds and just shuts off. Nothing happens when you push the start button.


Hi

If clean light is blinking 7 times then it may be an issue with heater circuit, door switch or wash pump. If yes then please reset the power to the dishwasher. After, 5 minutes check if you are still getting the same error. If yes, then it is a water heating fault. To resolve this error try pressing this reset sequence-- Heat Dry - Normal - Heat Dry - Normal or High Temp - Air Dry - High Temp - Air Dry or Hi Temp Scrub, energy saver dry, Hi Temp Scrub, energy saver dry. Now let the unit run for 2-3 minutes and then you press the Cancel/Drain button and allow it to completely drain and reset.
If this doesn't work then it's an issue with the wash pump not pumping the water past the heater efficiently or due to lack of water to heat. Please make sure that heater is not open circuited and is heating the water efficiently. You'll have to check the heater using a multimeter; the meter should read between 3000 to 3300 ohms (Use multimeter on Rx1 ohm setting). If heater is fine then make sure water pressure is optimum and fill valve is working fine. Hope this helps... Please post back for further assistance.

Daniel

Jan 01, 2011 | KitchenAid Dishwashers

1 Answer

When i push the start button,it doesn't light up and start. The normal cycle and the other cycles lights work but it won't start. If i push hi-temp wash and heated dry several times, all lights will come...


i would replace the key pad it sounds like since everything else works.. so you hit the normal wash and start the dishwasher sits there for a min or two and turns off.. Its not recognising the start button

Sep 03, 2009 | Dishwashers

1 Answer

I have a GE QuietPower3 dishwasher... the normal wash, heated dry, hot wash and hot start buttons are all flashing... can you tell me what is going on please?


try this, I was researching and found that this solution worked. While all the lights are blinking, close the dishwasher door and let the machine run through the cycles. This actually happens pretty fast. Then it will stop and quiet down and all the blinking lights will shut off. Then just press the buttons you want and hit start and the machine will start. The time it takes for the blinking light to shut off is about 1 to 2 minutes. It worked for me.

Aug 09, 2009 | GE Dishwashers

1 Answer

Kenmore Elite Dishwasher clean light ind flashing and won't start


That means the control sensed that the heater in the d/w did not operate 3 times in a row. so the unit locks out. First remove the kick plate and you may have to pull the unit out from under the cab, but check your heater. use a meter to see if it reads open, if so order a heater assy it will come with a new control replace it to. If your heater checks good press in sequence normal wash , heat dry ,normal wash,heat dry , normal wash , heat dry three times within 6 sec all the lights will come on then hit cancel. What that did is reset the control and clear that fault. Keep in mind that d/w does not heat it's own water your incoming water temp should be 120. the d/w will maintain that temp. when starting your d/w first turn on your hot water till it gets hot then start your d/w this insures your unit fills with hot water and not cold

Jan 09, 2009 | Kenmore 24 in. 15142 Built-in Dishwasher

1 Answer

GE dishwasher won't start


You have a washer control board problem or a burnt connector or both.

Mar 17, 2017 | GE 24 in. Profile PDW9200J Built-in...

2 Answers

Kenmore Dishwasher displays the number "98"


I have a very similar problem. When I push a wash selection, every light on the panel shows up...and when I push Start, nothing happens. When I push cancel, it trys to drain, even tho no water is in there any more. Have you ever had an answer to your problem?

Feb 06, 2008 | Kenmore 16872 Built-in Dishwasher

20 Answers

Kenmore dishwasher wont start blinking clean light


today January 9, 2009...blinking clean light, kenmore dishwasher would not run,,,the solution on Fixya ..."keep hitting normal -heated wash-normal -heated wash buttons over and over...unlocked the blinking green light problem. Dishwasher is running as I type this....will post again when I see the results of another washing tomorrow. H.T. Las Vegas Nv

Jan 18, 2008 | Kenmore 16602 / 16604 / 16609 Built-in...

12 Answers

Clean light keeps blinking and I can't start a new cycle


Puppa, clear the fault by pressing the keys in this order: high temp scrb--air dry--high temp scrub--air dry. Or, depending on your model..Sani rinse--air dry--sani rinse--air dry. The dishwasher will enter the service mode. Let it do it's thing or advance it through it by pressing the start key. The fault came from the board not sensing a rise in the water temp. Make sure to run the hot water before starting the dishwasher. The heating element runs through the nuetral side of the door switch so make sure the d/w is level and the door switches are all making. The element itself could be at fault. Catriver...post back

Apr 01, 2007 | Kenmore 24 in. 15932 Built-in Dishwasher

Not finding what you are looking for?
General Electric Adora GHDA670N Built-in Dishwasher Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top GE Dishwashers Experts

Mike

Level 3 Expert

4362 Answers

Archie Ferrarini
Archie Ferrarini

Level 3 Expert

869 Answers

Vitally Alcher

Level 3 Expert

1645 Answers

Are you a GE Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...