Question about DISH Network 142923 Remote Control

1 Answer

SAT button not working on remote--volume controls work to the TV--screen is displaying Press Select to Contine--when pressed red SAT light does light up but nothing happens

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • DISH Network Expert
  • 286 Answers

Hello, there! My name is Becki Barned, with Dish Network customer service. You have probably already getten this resolved, but just in case it happens again, or you have questions, here is a link to our website, where you can take the steps to reprogram your remote, which is what is needed in this case. http://www.dishnetwork.com/SupportSection/remote-control I hope this helps in the future!!!

Posted on Dec 28, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The tv is jammed. Remote is fine but have pressed the wrong button


It sounds as though you might have just accidentally pressed a button and changed the remote into an incorrect mode for example, tv, or aux modes. This would in fact prevent the remote from successfully working with the DISH Network receiver. If this is in fact the problem, then the remote simply needs to be put into "SAT" mode, once its back in SAT mode you will then be able to change channels, select menu, power receiver on and off, etc. The "SAT" button is labeled & in the upper left hand corner of the remote to put the remote back in satellite mode, please just press that SAT once and then release, the SAT button should briefly light up red & then the light will go out, you should then be able to use the remote again, to ensure remote was successfully changed back to SAT mode, you can press select or any other button you chose & as long as the SAT button lights up when you press another remote control button- then your all set to go & everything should be working once again! I hope this helps -please let me know if there is anything else I can help you with!
-Kirstie DISH Network

Oct 01, 2010 | DISH Network IR Remote Control

Tip

Harmony remote is not controlling Dish Network device.


Hi. For most Dish Network devices, you will have to ensure that the remote address is set on 1 in order for it to be controlled by the Harmony remote.

To reset your Dish Network device to remote address 1, you can do the following:


1. Press SYSTEM INFO on the receiver's front panel. The System Information screen displays on the nearby TV and shows the Remote Address.
2. Using the original Dish Network remote, press and hold SAT on your remote control for about three seconds, until all of the mode buttons light up, and then release SAT.
3. Using the NUMBER PAD, press the 1 button.
4. Press POUND (#). If you entered the address correctly, SAT will flash three times.
5. Press RECORD. Make sure the Remote Address you see on the System Information screen is 1.
6. Press the SELECT button on the front panel to close the System Information screen.


That should get the device working with your Harmony remote.
Hope it helps.


Sources: http://support.logitech.com

on Mar 10, 2010 | Audio Players & Recorders

1 Answer

Dish network control not working on 2nd. tv


You have a dual receiver and 2 remotes. make sure that receiver is in dual mode. That you press the sat key on remote 2 if it will still not operate take remote 2 to the receiver. With remote #1 press the menu button twice you should then be on they system info screen. Pick up remote #2 press and hold sat key until it blinks press record 3 times . press red power button and if tv2 light goes off and on the remote should work again for tv2 . Use remote #1 press select exit screen,

Jun 02, 2010 | DISH Network IR Remote Control

1 Answer

My new dish net remote will not work on my 3100 reciever. Any ideas?


Hi. You may want to check the remote address settings.

1. Press SYSTEM INFO on the receiver's front panel. The System Information screen displays on the nearby TV and shows the Remote Address.
2. Using the Dish Network remote, press and hold SAT on your remote control for about three seconds, until all of the mode buttons light up, and then release SAT.

3. Using the NUMBER PAD, press the 1 button.

4. Press POUND (#). If you entered the address correctly, SAT will flash three times.

5. Press RECORD. Make sure the Remote Address you see on the System Information screen is 1.

6. Press the SELECT button on the front panel to close the System Information screen.


Hope that helps :)
(source: support.logitech.com)

Mar 18, 2010 | DISH Network IR Remote Control

2 Answers

TV or control doesn't work need help know


ok my tv is doing the same thing and i need help if you found a solution please email me at pieces41096@aol.com

Jul 06, 2009 | DISH Network 322 DTV Receiver

3 Answers

Technika sky code volume needed 42-502


0246 is the code 1st cover the top of the remote with your hand press TV you can now move your hand, now press and hold select and the red button togeather the remote light will flash twice enter the code 0246 then press select cover top again and press SKY button it should now control your tv

Jun 03, 2009 | RCA DIRECTV Satellite Remote Control

1 Answer

My volume and mute button dont work on my sky remote


panasonic

please follow the steps below:

TV
RED + SELECT
TV
0051

try the volume if this works then press SELECT to save the code. If not then press TV again then the volume. repeat this step until the volume works then press the SELECT button to save the code.

cheers

Little Dish Fitter

May 06, 2009 | Universal Remote Control Remote Control

1 Answer

118575 remote stopped working batteries are new lights light up but wont control tv or satellite anymore even though it just worked


The receiver more than likely received a software update or reset itself and reset the codes to the receiver and tv. We will need to set the remote address again and run a power scan to control the tv. Using the front panel buttons on the receiver press the menu button twice. This will put you at the system info screen. You will see the remote addresses for tv 1 and 2. They will probably both be set to 1 if the receiver reset. Press and hold the SAT button on the TV1 remote until all lights across the top light up and release. Now key in a two digit number between 1 and 16 (for 1-9 precede that numeric with a zero) now press the pound key at the bottom right of the remote numeric keypad. The SAT button will flash three times and press the record button until the remote address on the screen displays the one you entered. The receiver should now be able to be controlled by the remote. Now we need to do a power scan - press and hold the upper left TV button until all buttons across the top light up and release. Press the red TV button and release, The TV button should be lit constantly. Now press the channel up button slowly until the TV turns off. Once it does press the channel down once and then cannel up to see if the TV turns back on. If it does press the pound sign. Now press the record button and you are back in business. If you have further issues let me know. Thanks for using Fix Ya.

Apr 03, 2009 | DISH Network IR Remote Control

1 Answer

Remote code needed (sky+) to sync with Sony bravia kdl32v2000


1. Press tv on your Sky remote control.

2. Press and hold down select and the red button together until the red light at the top of your Sky remote control flashes twice.

3. Press tv again

Then enter the remote control code using the number keypad. The red light will flash twice if a valid code has been entered.

Sony Code: 0000

4. Point your Sky remote control at your TV and press the Power button. If this turns the off as you'd expect, then the tv should be set, press Select and the remote should work

5. If the TV does not turn off press tv, then press the Power button again, repeat this process until the TV turns off, when the TV turns off press Select.

Jan 16, 2009 | Sony BRAVIA KDL-32S2000 32 in. LCD HDTV

2 Answers

The volume control won't work on my sky remote


for a toshiba tv,

press tv
press and hold select and red until the led blinks twice
type in 0 1 5 6
press the power button on the remote

If the tv turns off press select and hey presto you're done, if the tv doesn't turn off, press tv then press the power button and keep doing this until the tv turns off. When the tv turns off press select.

Nov 17, 2008 | Universal Remote Control Remote Control

Not finding what you are looking for?
DISH Network 142923 Remote Control Logo

530 people viewed this question

Ask a Question

Usually answered in minutes!

Top DISH Network Televison & Video Experts

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

matt martin
matt martin

Level 3 Expert

1257 Answers

Are you a DISH Network Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...