Question about D-Link 802.11g Wireless Router WBR-1310 (WBR1310)

3 Answers

D-Link Wireless Router WBR-1310, Version A1

Our router stopped working. I have my main computer connected to modem, and internet is working fine. But my wireless laptop (XP), my wife's computer (Vista), and my son's computer (XP) can't see the network. I've tried shutting everything down and rebooting. I've tried hitting the reset button on the router.

Posted by on

  • 2 more comments 
  • Anonymous May 02, 2008

    Went away for a few days and came back to find the router not working. Although the cable modem was fine, there appeared to be no communication between it and the router. Powering both down did not help. Nor did resetting the router back to back to factory settings. When I try to re-install the router, I get a message "error: internal error". At this point, I'm afraid that the router is fried - and of course - one month after the 1-year warranty expired. Any help would be appreciated!

  • geethar6 Aug 04, 2008

    Hi,



    I bought this router newly and tried powering it on, and it gave a green status light. But after a couple of days, when i tried connecting it, it used to not switch on. In the middle, this router got dropped down once. I have tried pressing the reset button for a few seconds and it din't work up. Is there a suggestion to fix this problem.



    Regards,

    Geetha.

  • Anonymous Aug 06, 2008

    I had the same problem. I just woke up one morning and it didn't work. I called the support hotline and they ran me through some options like hitting reset etc. before conculding that it was dead. They were able to send me another router in the mail at no cost (except for the cost of shipping the dead router back to them). Unfortunetly, the new router they sent me was also dead and their customer service is less than helpful this time. I would suggest just buying something else.

  • Anonymous May 04, 2009

    I've had the same problem as everybody else, I came back after the long Easter weekend and viola - only power and not status light, it was as if the router was getting no signal of an internet connection. I called up the tech support and they asked me to hit the reset button and nothing happened even after powering it off. I'm well over a year (1.5 yrs or so?) so no warranty is covered under mine.

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

ø1 i what to know if this suport is avaliable in french
ø2 i always get an error whit the dns server ( found it whit msn messenger ) for iformation mi own is wbr1310_revB_firmware_202
ive tried to update de firmware but dosent work :(

Posted on Aug 07, 2008

Ad

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 537 Answers

Make sure you fully reset the device to its factory settings. I am not sure on the DLink what the procedure is. Usually it's unplugging the unit, pressing the reset button for 10-30 seconds, then repowering on the unit.

From a wired laptop, reinstall the software using the CD that came with the unit to set up the router. Your manual should cover all of this. If you don't have the manual/software, re-download it from D-Link's web site.

If the router will not power on or give status lights, then that's another problem entirely.

Mike

Posted on Apr 27, 2008

Ad

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problem.

Make sure you turn off all the security with the software in package then slowly turn it all back on, on piece at a time. For whatever reason, it comes with MAC address filtering already turned on, which makes it impossible to see if you don't have the right info put in to the computer that the router was configured with.

Posted on Feb 27, 2009

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

For no reason, my HP laptop stopped working the internet. It works perfectly otherwise. I hard connected the laptop directly to my wirelessouter as well as my modem, still it will not connect to internet.


Connectivity issues can be many.

I would start my first rebooting the main modem.
Once that is up, reboot the wireless router.
Once that is uo, reboot the laptop.
Try to connect.

If that does not work, eliminate the wireless router and connect the laptop directly to the modem via Ethernet cable and reboot the computer again and see if it works. If it does, then it is something with the wireless router. If it doesn't, i would contact the provider so they can verify that they can see your modem on their network. If they cannot, they will advise you further (hardware/cabling issue). This is all assuming that nothing has been changed on any settings of the laptop, router or modem.

Jul 21, 2010 | HP Pavilion dv6000z Notebook

5 Answers

My daughter works at home as a Customer Service Rep. for Generation Networks (Ancestor.com). She has a terminal from work and it is configured for her to work from home. She has done that for over a year...


This is only a problem with the firmware of your modem/router that you need to update it, because a network device like a modem and router that is working fine for severla years and suddenly stop working you just need to update the firmware of it and it should be working fine again, to update the firmware of the modem/router just need to call the manufacturer for that....

Hope that helps.........

Oct 05, 2008 | Computers & Internet

1 Answer

Belkin router can't connect to internet


This is part solution, part clarification request: When you say that you installed the setup software on your laptop, setup software for which: the modem, or the belkin router? Also what type of internet service do you have - Cable? DSL? If you are not sure, list your ISP. What operating systems do you have on your laptop and your main computer?

You say that you connected the modem to your main computer - I am assuming that you mean that you connected your modem with a network or ethernet cable (the one with a connector that looks similar to but larger than a telephone's connector) to your computer's ethernet card, or NIC, port. Is anything connected by ethernet cable to the Belkin router? If you have not connected the modem directly to the router, it will not connect to the internet, and anything connecting to the Belkin router will not be able to access the internet as well.

Try this: disconnected the power from your modem, then disconnect power from your router, and disconnect any ethernet cables from computer & modem, or computer and router. Connect an ethernet cable from the modem to the Belkin Router. (Ensure that you have plugged in the ethernet cable on the router into a port that is either set aside from others, or indicates "Internet", WAN, or something similar - it should be marked either with a different color, labled, or both). Now power on your modem. Wait until you see a steady "ready" light, green ethernet light, or the light usually lit for that model indicating it has completed its bootup tests and the internet connection is ready.
Next, ensure the ethernet cable is connected from the modem to correct WAN or "internet" port on the Belkin Router, then power up the router. Once the router boots up completely, plug in a cable from your computer's (main computer) NIC or ethernet card or port, to a port on the Belkin Router (there should be more than one port available, generally numbered "1, 2, 3" and so on - in a group, seperate from the WAN or internet port). Once you are sure you have the cable plugged into one of the correct ports, and if you have windows, restart your main computer.

Now on your main computer, check to see if you have an internet connection. If you do, you can now resume running the router's software setup on your laptop, which sounds as though it was walking you thru the setup process to connect you via wireless connection to the internet. Report back if you have any success, or if you have any further problems, and best of luck! Hope that info helps

May 05, 2010 | Belkin (F5D8231-4) Wireless Router...

1 Answer

My wireless hp says router cannot find host name


Double check your physical connection. It should be this way

Modem > connected to Internet Port of the router
PC > connected to port 1
Laptop > can be wireless

Now you must power cycle your router and modem. Turn off router first then modem. Wait for 30 seconds. Power on modem first, then the router. You must configure the wireless settings on your laptop it doesn't connect automatically.

Jun 14, 2009 | D-Link DIR-625 (790069292637) Wireless...

1 Answer

Wireless network access: 1 laptop fine, other not so much


Check the wireless card on the PC first. Go to "My Computer" then "Device Manager" and check to se if all the hardware is ok.

Use Control panel/netconnections to check to see if you still have a wireless connection and if it works. Also check "My Network Places." Try re-installing the drivers.

As a last resort....try System Restore if it's an XP or Vista system. Remember - using system restore will return the PC to an earlier time but you could lose some stuff so decide first.

Mar 21, 2009 | Acer Computers & Internet

1 Answer

Internet connection between linksys router


May be your router internet settings has been wrong. you must reset the router settings by clicking the router reset button. Pls locate the button and then put the internet cable into router internet port.

Jan 03, 2009 | Linksys Wireless-G WRT54GS Router...

1 Answer

Connection to my Desktop not working.


Try and change the cable from the router to computer with a new one and do the same with the modem and see if connects. Hopefully it's just the cables that are faulty.

Aug 11, 2008 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

Router seems to drop connection frequently


What a static ip is, is the ip address that the router automatically assigns to other equipment. (computers, xbox, ect.) Find D-links customer support line for help.

Apr 11, 2008 | D-Link DIR-625 (790069292637) Wireless...

1 Answer

Server not found} NetGear WGR614 Wireless Router doesn't connect me to the internet.


Dear Loud Nouises,

Your router must be connected properly to the cable modem. This must be to the wan port on the router.

Next, the router must be set-up accordingly to recognize the modem's internet connections. Please ask for the IP address.. and other relevant informations from your internet provider.

Set -up your computer using the internet connections wizard on each of your respective computer.

This should work fine if all connections were correctly configured.

Sidlahora

Nov 27, 2007 | NetGear WGR614 Wireless Router

Not finding what you are looking for?
D-Link 802.11g Wireless Router WBR-1310 (WBR1310) Logo

4,140 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2277 Answers

Ekse

Level 3 Expert

13434 Answers

Mike

Level 3 Expert

4363 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...