Question about Reliance Natural Gas Water Heater Control

1 Answer

The red light on the water heater keeps flashing

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 494 Answers

Attached to the water heater is a troubleshooting chart for your sequence light. 1 flash means..., 2 flashes means...., and so forth. Find the chart, count the flashes and see what it means and we'll go from there. Douglas

Posted on Sep 18, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a valliant atmo gas water heater and no hot water just the red bulb flashing


Gas (natural or propane) water heaters require electrical power to make the igniter work. The most common source is two (2) D batteries. When the batteries become weak an visual alarm will be visible, such as a red blinking light. Try installing new batteries.

Oct 10, 2016 | Water Water Heaters

1 Answer

Flashing red light mean


copy following link to identify water heater gas control valve:
http://waterheatertimer.org/How-to-troubleshoot-gas-water-heater.html#intellivent

Gene
h

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Mar 17, 2014 | Reliance Water Heaters

1 Answer

Water is cold and the light keeps flashing need to troubleshoot it


Light flashing while water is flowing means you have a bad control board. Needs to be replaced. They can be purchased online

Nov 23, 2013 | Bosch PowerStar AE115 Tankless Water...

1 Answer

My red light is flashing


Gas water heater?
Copy following link to troubleshoot be gas control valve:
http://waterheatertimer.org/How-to-troubleshoot-gas-water-heater.html#intellivent

Add comment and describe type and brand of water heater

If you need further help, I’m available over the phone at https://www.6ya.com/expert/gene_9f0ef4df2f9897e7

Mar 29, 2013 | Bosch & Tankless LP Hot Water Heater

1 Answer

Should the red lights be flashing or be on steady


A solid light is what you actually want.
If you have a blinking light, the unit is unable to keep up with the flow of water.
Slowly turn on the hot water for your bathtub until the light starts to blink to find your limit. in other words your tankless heater is too small for your needs.
The 24 model is more for houses with showers or slower flow.
The 36 or higher model has 3 sets of heaters to be used with a bath, higher flow.

Jan 20, 2013 | Stiebel Eltron TEMPRA 24 Tankless Water...

1 Answer

Faulty Junkers water heater


first find out from your manual what the flashing red light means...that should narrow your search---could be a thermocouple shot,a rubber diphragm in the gas valve has weakened and not operated, or gas pressure into the appliance may suddenly be too low, or springs in gas valve may have worn out---very many possibilities

Mar 02, 2010 | Water Heaters

1 Answer

No heating and hot water


sounds like overheat stat easy job to replace and do,nt cost the earth best of kuck

Oct 14, 2009 | Water Heaters

1 Answer

I have a digistat scr with a flashing red light and no heating there is nothing wrong with the batteries, this only occured after a poweer cut.


Try this first before condeming the unit.

1. Turn off the power supply to the Digistat SCR (receiver unit)
and leave for 5 seconds.
2. Turn on power to SCR unit and check red light is on.
3. Press override button No.2 and check the green light comes
on and boiler fires.
4. Press & hold down button No.1 (Keep depressed), then
press No.2 and keep depressed. {The Red LED light will flash
a couple of times and then it will go out}
5. Now release both the buttons – {the two LED lights should
come back on}
6. Get the Digistat+2RF/+3RF unit and stand two metres away
from the SCR unit with the Digistat+2RF/+3RF unit in your hand.
7. Remove the battery cover and fit the batteries.
8. The Red LED light on the SCR will now flash for approx. 7
seconds.
9. This confirms that the radio signal is being sent and
received.
10. The Digistat+2RF/+3RF and the SCR are now successfully
linked by a dedicated RF address.

Mar 21, 2009 | Water Heaters

Not finding what you are looking for?
Reliance Natural Gas Water Heater Control  Logo

Related Topics:

4,924 people viewed this question

Ask a Question

Usually answered in minutes!

Top Reliance Water Heaters Experts

Gil Shultz

Level 3 Expert

3388 Answers

Paul Nielson
Paul Nielson

Level 2 Expert

92 Answers

Norman Worley

Level 3 Expert

1273 Answers

Are you a Reliance Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...