Question about Sony STRDH710

1 Answer

Is the sub out strictly for a powered sub or is there a way to hook up speaker wired subs to that

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 583 Answers

The sub out connection is for powered subs. To use a sub that runs off of the amp power, you'll will have to run it through the main speakers. Usually, on this type of sub, there are connectors that allow the frequencies above the sub range to bypass it and go on to the main speakers (the sub filters the lows and passes the highs on to the speakers). If your sub does not have this, then you'll have to get a separate amp for your sub to run off of the sub-out.

Posted on Dec 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 2 10" Kicker Comp Subs


That amplifier is only rated at 150 watts at 4 ohms, or 300 watts at 2 ohms. Not a very strong amp to run 2 kicker comps. My guess is you have the subs wired wrong for your application. There are 2 types of subs, one is a dual 4 ohm, and one is a dual 2 ohm. Most people bridge these coils together and that cuts your ohms in half. For example. Lets say you have the 10cvr104 subs. Thats the dual 4 ohm sub. You wire the coils together in parallel, now its a 2 ohm sub. You have 2 of these subs running off of your amp, if they are hooked up in parallel, now you have a 1 ohm load, out of the amplifiers normal operation. Your amplifiers internals heat up really quick and there is a thermal overload, putting your amplifier into circuit protection mode. My suggestion for wiring your subs is as follows: for each speaker, wire the coils together like this- positive coil1 to negative coil 2 and negative coil 1 to positive coil 2. That is called running in series, and doubles your ohm load. Next, we need to wire the speakers together properly to hook up to your amplifier. For this, since the coils are hooked together, you only need to use one set of terminals from each sub. And take the positive from sub 1 and hook it to positive of amp. Take negative sub 1 and hook it to positive of sub 2. Take negative of sub 2 and hook it to negative of amp.

Aug 30, 2012 | Rockford Fosgate Punch 301M Car Audio...

1 Answer

My celestion s20 subwoofer won't play if i hook it up to sub out on receiver.but will play if i run a regular speaker wire to it. I know sub out is working on receiver.


Tell your source (receiver???) that it has a sub and set it up to feed LFE out of that RCA jack.

Prove your sub pre-out works. Or send something like FM on Tape Out to the sub and see how that works out.

How did you hook a speaker wire to this model of powered sub? What was on the other end of that speaker wire? It's not designed for speaker level input.

Jan 28, 2011 | Celestion S20 Subwoofer

1 Answer

I have 2 sony xplod 4ohm subs rated 350w rms and 1200w max, i have them in really shallow boxes because i drive a single cab toyota, i know these subs **** but i do also know that they can hit alot harder...


the premier amp is better since it has a better rms rating (360w total or 160w each sub) than the eclipse (280w if you bridge all 4 channels which isn't possible but 140w for each speaker bridging 2 channels per speaker). Neither are going to push your subs but if you get another amp wiring kit and use one amp per sub they will sound a lot better and you could just hook both power wire and ground wires from the bridged channels to the power and ground terminals for the sub. That would be my suggestion since the subs are rated at 350w and each amp is 280w and 320w which will push but not blow the subs.

Aug 17, 2010 | Sony Car Audio & Video

1 Answer

How do I hook up a non powered sub woofer on my htr-5630?


You will need an amplifier or 2 channel receiver. Hook the sub out rca jack to the rca inputs on this new amp or receiver and hook the speaker terminals on sub to speaker terminals on same amp or receiver. Your Yamaha receiver doesn't have any power for a passive sub.Just pick up any old fairly high powered receiver for fifty dollars and you're good to go.I use old dolby pro logic receivers as they are a dime a dozen today. Good luck.

Feb 20, 2010 | Yamaha HTR-5630 Receiver

2 Answers

Connect stereo amplifier to powered sub


You can y out from the main out to the sub.This output is post volume control. set level on sub to desired balance of lows feq to highs

Nov 20, 2009 | Yamaha YST-SW015 Subwoofer

1 Answer

My subs are ***


try taking one wire out of one sub, if the single sub gets louder than both then your wires are out of phase, if not then there is a prblem somewhere else.

Sep 10, 2009 | Alpine SWR-1240 Car Speaker

1 Answer

Powers up but no speaker output


Hello montez1599,

That's a great amp.

You do not say what subs you are connecting or what wiring configuration you are using. But there should be no problem if the amp is powering up normally. I'd check the gain and crossover settings to make sure they match the subs.

Having 2 +'s and 2 -'s is just a convenience for connecting more than one sub to the amp. If you have just one sub, connect to either of the positives and either of the negatives (they're connected internally). If you have 2 subs, you can run separate wires to each sub or you can wire the subs together and then run just one positive and negative to the amp.

Hope this helps.

Aug 30, 2009 | Jl Audio 500/1 Car Audio Amplifier

1 Answer

Can i hook up a powered 12'sub to a Pheonix Gold xs2500 amp without blowing the speaker


First I hope you remove the speaker wires from the speaker that come from the built in amplifire. You cannot hook the powered sub to the amp without doing that first. Then all you need to do is run speaker wire from the sub out of the box to the amp. In no way can you hook up any other part of the powered sub, but the sub itself, to the amp. If you know the wattage of the sub and the ohms then wire it to the amp correctly. Your phoenix amp will put out 125 watts x 2 at 4 ohms and 250 watts x 2 at 2 ohms and 500 watts x 1 at 4 ohms bridged. Remember, only the sub itself in the sub enclosure can be connected to the amp. Hope this helped you. Let me know if you need more help.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/mark_b53a7494531bf96d

Aug 23, 2009 | Phoenix Gold XS2300 Car Audio Amplifier

1 Answer

Powered Sub, no output


does the sub have speaker wires in and out run fronts wires from sterio fronts to theins of sub then outs form sub to fronts ok set cross over at 100 or so

Jan 24, 2008 | Audio Players & Recorders

2 Answers

Adcom GFA-5400 installation


Use the niles for more than one speaker hookup. As far as the sub hookup, use a powered sub with speaker inputs
then use the right or left speaker and tag a couple wires to the sub. Good Luck
BIGRED

Dec 28, 2007 | Adcom GFA-5400 2-Channel Amplifier

Not finding what you are looking for?
Sony STRDH710 Logo

Related Topics:

1,190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sony Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5686 Answers

The Knight
The Knight

Level 3 Expert

76125 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Sony Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...