Question about Danby DWC513BLS Wine Cooler

1 Answer

Fridge does not get cold , " E4" displayed on

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Change digital board in the front

Posted on Aug 18, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electrolux fridge temperature control displays a "square"


Try lower either the thermostat setting or the airflow control to the refrigerator to see if the temps are lowered.

Nov 26, 2013 | Electrolux Frigidaire Fridge Defrost Timer...

4 Answers

Termperature Control


Well, the control circuit get input from thermostat.
what you need to change is right the thermostat. I do not think there is any way to lower fridge temp if you do not replace thermostat.you could put an additional switch to turn on/off manually the compressor when you need extra cold, but in this way you risk to damage the motor.
You need to change the thermostat with one that switch on at a lower temperature. to do this you may need to use a non-fabric part.

regards

Mar 10, 2008 | Refrigerators

2 Answers

My Danby refrigerator stopped working after the power went out over the weekend. I have adjusted the temp. dial but nothing appears to make a difference. Is there anything I can do to reset the fridge?


Try to unplug it again let it set 5 min and then plug it back in. If that doesn't do it you may have to replace the compressor relay where the wires hook to the compressor, thats a fairly easy fix on that unit.

May 17, 2011 | Danby DAR483 Compact Refrigerator

1 Answer

E4 Code


Between phone calls to danby and my neighbor, we fixed this problem. My E4 was on the left (lower chamber). If you have one on the right it is the upper chamber. The E4 is a defrost sensor that can be ordered from Danby's distributor (call Danby for the one in your area). The part and shipping were around $30.

If your E4 is on the left...

- remove the top shelves
- open the cover inside the cooler above the digital read outs (the top unscrews)
- inside is were the repacement sensor plugs in
- replace the one with the long cord
- run the sensor down the back to the lower chamber
- replace all covers and parts

If the E4 is on the right...

- remove the top shelves
- look on the right hand wall for a black plastic grate, the sensor is under this grate
- replace the sensor (simple plug and play)
- replace the racks.

Please pass this on, it was a ***** to deal with Danby and I nearly trashed the cooler out of sheer frustration.

Nov 17, 2008 | Refrigerators

10 Answers

Whirlpool Beverage Center (WBC127BLS) - Won't cool enough


If you're handy with a soldering iron, it's possible to 'trick' the fridge into cooling down a few more degrees.

Long version:
If you open the door to the fridge, on the right wall near the bottom is a small plastic grate. You should be able to pull this straight out from the side wall. There is a temperature sensor attached to the back of the grate. Unplug the sensor. (The fridge will then give you a very annoying error beep and display "EE" on the readout. Pushing the °F-°C button stopped the beeping.) This sensor will change resistance with temperature. (The lower the temperature, the higher the resistance) I was reading a resistance of about 3700 ohms at 43°F and 2460 ohms at 68°F. Throw in a rough assumption that the response is linear and it works out to almost 50ohms/degree. In order to 'trick' the fridge into cooling down more, you need to drop the resistance. I was aiming for about 6 degrees cooler. Assuming the resistance response was linear, 6 degrees cooler would give me about 4000 ohms from the sensor. By jumpering a 50000 ohm resistor (yes, 50K ohm) in parallel with the sensor, I should get about 6 degrees cooler. I did the soldering, plugged the sensor back in, and ended up about 8 degrees cooler. Two days so far, everything appears good and the beer is cold.

Short version:
Put a 50K ohm resistor in parallel with the temperature sensor behind the grate on the inside right hand wall.

The temperature read out will be inaccurate forever after though. But then, I just want cold beer, my wife wants cold water, and the kids want to play with the cool blue light. I don't care what the number on the readout is.

Oct 03, 2008 | Refrigerators

3 Answers

Danby DWC283BLS Wine Cooler - Error message E3 & E4


Is the compressor running? I don't know this unit, but know that if you are too warm that is the first thing to check. In reading about another unit that had a different problem, it was mentioned that there is a ciruit board. If it has relays on it then these are the most likely culprit. They are either not making contact or staying in contact too long... sometimes just tapping each relay usually a black plastic component will cause it to work intermittently..Not sure if you can get these but call the company help line at 1-800-263-2629.

Jun 12, 2007 | Danby DWC283BLS Wine Cooler

Not finding what you are looking for?
Danby DWC513BLS Wine Cooler Logo

Related Topics:

897 people viewed this question

Ask a Question

Usually answered in minutes!

Top Danby Refrigerators Experts

William Miller
William Miller

Level 3 Expert

9173 Answers

Cindy Wells

Level 3 Expert

5938 Answers

Marvin
Marvin

Level 3 Expert

85108 Answers

Are you a Danby Refrigerator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...