Question about Jandy Aqualink Rs4 One Touch Control System Control System

1 Answer

How do I delete an Aqualink RS4 program? The filter is on all the time. When I set a new program start and stop time the controller keeps adding programs versus replacing an/the existing programs.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Jandy Master
  • 10,259 Answers

To delete a program go to system set up go to programs add or delete or edit if doing on its own disconnect spa side remote if goes away replace spa side remote if no spa side reset board clear memory and re program write down all auxs and JVAs

Posted on Jan 30, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 22 Answers

SOURCE: Need to clear a program from my aqualink

Start with the cancel button. It will then prompt you to cancel the desired program. Go through the menu as you would with a program but follow the prompts to cancel. Remember, press cancel to start.

Posted on Dec 30, 2008

  • 22 Answers

SOURCE: I need to clear a

Start with the cancel button and follow the prompts

Posted on Jan 01, 2009

  • 15 Answers

SOURCE: I have an Aqualink RS4. I want to delete the 3

The best thing to do is to clear the system memory. Aqualink can have a problem with "ghosting" Things just go on by themself when not programed to. A bad spa side remote can do that to but that is another problem.
To clear the memory
Push the menu button once
Push the back arrow to "System setup"
Push star * or enter button
Push back arrow till diplay says " clear memory "
Push star or enter
Push star or enter again to comfrim.
You will get a message "earsing memeory"
Now you can reprogram system
If you want differant run times like a summer and winter timing you can do that with the program groups

Hope this helped
Keith

Posted on Jun 23, 2009

  • 2 Answers

SOURCE: Jet blower randomly starts ...

most of the time this is caused by a faulty spa side controller. If you trace the line from the spa and disconnect it see if that solves the problem.

Posted on Aug 06, 2009

  • 5 Answers

SOURCE: pool lights go on randomly--not programmed to go on at all

make sure the light is pluged in a port that is for like a spare aux. any time you add programs you must hit the store button.

Posted on Oct 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Aqualink rs4 owners manual


go to system set up then go to program highlight what you want to program then add start and stop time if to run all the time start 2:00am and stop 1:59 am it will shut off for 1 minute then restart

Jul 21, 2014 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

Aqualinks rs4


Go to menu , program the pick pool and input your desired schedule.
Make sure the day and time is set correctly!

Jul 21, 2014 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

How do I cancel filter programs


go to system setup go to program if there is a program it will let you edit or delete

Apr 02, 2014 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

The inside control display on my Aqualink RS4 is red instead of green on the filter pump button. What does this mean?


either the temp is below 38 degrees if so it is in freeze protect if not 38 degrees or lower bad temp sensor go to system set up and go to program go to freeze protect and un check the filter pump

Feb 16, 2013 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

Program Group A is selected and the filter pump is programmed to start at 12 noon but does not turn on. If I start it manually, it runs fine and will turn off at the proper time. What could it be? ...


Check to see if your nine volt battery is good. The aqualink will hold it's programs but lose time and date. At that point it goes back to factory set. You have to have a fresh battery to avoid this.

Nov 30, 2010 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

Jet blower randomly starts ...


most of the time this is caused by a faulty spa side controller. If you trace the line from the spa and disconnect it see if that solves the problem.

Jul 24, 2009 | Jandy Aqualink Rs4 One Touch Control...

2 Answers

Need to clear a program from my aqualink


Start with the cancel button. It will then prompt you to cancel the desired program. Go through the menu as you would with a program but follow the prompts to cancel. Remember, press cancel to start.

Dec 26, 2008 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

Not finding what you are looking for?
Jandy Aqualink Rs4 One Touch Control System Control System Logo

Related Topics:

4,903 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

10259 Answers

Bill Jordan

Level 2 Expert

373 Answers

Anthony Davis
Anthony Davis

Level 1 Expert

61 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...