Question about Kyocera FS-2000D Laser Printer

1 Answer

Hi have an error call service 6000:0085594 My printer is Kyocera Fs-2000D If you can help me pls

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Kyocera Master
  • 525 Answers

Code: 6000
Contents: Broken fuser heater lamp wire
30 ppm model:
The temperature does not rise 1×C after
the fuser heater lamp has been turned
on continuously 5 s.
35/45 ppm models:
The temperature does not rise 1°C after
the fuser heater lamp has been turned
on continuously 5 s.
The temperature does not rise 1°C after
the fuser heater lamp has been turned
on continuously 10 s during waming-up
or at standby.

Causes:
- Poor contact in the fuser thermistor M connector terminals.
Check procedures/corrective measures:
- Reinsert the connector

Causes:
- Fuser thermistor M installed incorrectly.
Check procedures/corrective measures:
- Check and reinstall if necessary

Causes:
- Thermal cutout triggered.
Check procedures/corrective measures:
- Check for continuity. If none, replace the thermal cutout

Causes:
- Fuser heater lamp installed incorrectly
Check procedures/corrective measures:
Check and reinstall if necessary

Causes:
- Broken fuser heater lamp wire.
Check procedures/corrective measures::
- Check for continuity. If none, replace the fuser heater lamp

Posted on Feb 21, 2011

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, I have an ecosys fs 2000d, with a call service message 6000:0026965, somebody help me please


Call service message 6000 in Kyocera is a fuser error code. The fuser must have gone bad.

Regards,
Shrey

May 31, 2011 | Kyocera FS-2000D Laser Printer

2 Answers

I have a kyocera FS-2000D with error code: Call for service 0150:0000049. Help...thanks in advance


Error code 0150 is an engine EEPROM communication error. The engine board might need to be replaced. I have heard that sometimes a defective developer unit could cause this same error code. I would try swaping a develper from a working FS-2000D first.

May 20, 2010 | Kyocera FS-2000D Laser Printer

1 Answer

I have a kyocera FS-2000D with error code: Call for SErvice 0150:0000049. Help...thanks in advance


0150 is a problem with either the engine board or the EEPROM chip that sits on the engine board. If you want to do it yourself, you can open the printer up and reset the chip on the board as well as reset all of the connectors that plug into the board. Otherwise, your best bet is to call a Kyocera service technician.

Mar 17, 2010 | Kyocera FS-2000D Laser Printer

1 Answer

CALL SERVICE 6000:0115785


Error 6000: is a fuser error 0115785 is your page count. You require a replacement fuser

Apr 14, 2009 | Kyocera FS-2000D Laser Printer

1 Answer

Kyocera fs-2000d printer


A KYOCERA-MITA technician has to upgrade the firmware.

Jan 31, 2009 | Kyocera FS-2000D Laser Printer

2 Answers

Call service 7410:0100539 on a Kyocera fs2000d


I have heard that 7410 is a standard code meaning the drum is out of position. Seat the drum correctly and away you go.
David
www.copycare.net

Jan 21, 2009 | Kyocera FS-2000D Laser Printer

1 Answer

Regardin kyocera FS-2000D


The files called 2000sys.zip & 2000_eng.zip I beleive, if that helps. I bet after you have updated the firmware, you will find the serial number absent from status page, muz get corrupted when the engine firmware chucks the 150 error, Just thought I'd say although is not norm a problem

Oh, It only ever does the 150 once, never if firmware is updated.

Nov 12, 2008 | Kyocera FS-2000D Laser Printer

1 Answer

ERROR CODE 7410:0004729


Hi, switch off printer ,just open cover(door) on the left side of the machine and push Drum Unit in machine(to proper seat)
You have to hear "click" sound.Switch on printer.
Regards...

Mar 08, 2008 | Kyocera FS-2000D Laser Printer

Not finding what you are looking for?
Kyocera FS-2000D Laser Printer Logo

297 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

gggg

Level 3 Expert

904 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...