Question about Casio Sea Pathfinder Sports Watch (SPF-60D-7AVDR)- SimplyRun Watch for Men

1 Answer

Hello sir i have a casio spf 60d.when it runs in depth meter mode it suddenly blocks and does not operate or changes mode at all.An alarm that says RECOVER appears on the screen.after a while all of a sudden it all comes back to normal but all the depth information that was saved is lost.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,691 Answers

I suspect there is water leaking in to the sensor unit circuit located just behind the sensor. The Casio service would change the sensor, and all the gaskets in the watch. Then do a water pressure test on the case and etc. to make sure no leaks. I do not think you can service this yourself. You would have to know exactly the parts to buy and have the tools, and the pressure chamber to verify the gasket seal performance.

You should send it to Casio with a copy of your complaint. Look up Casio on the Internet and choose your country. Go to support to find the service address and instructions of where to send the watch. If you email them it can take a few days till they respond. They will send you the specific instructions. Their service is terrific. I own a number of their high end watches. In fact I have one with them being serviced. Sometimes I have broken the glass because I am rough with my watches at times.

Posted on Feb 11, 2018

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Casio spf 40 Module 2273

Your Watch is in Auto or demo mode. Hold down the "Mode" button for 3 - 5 seconds and it will return to time keeping mode.

Cheers,
Murray

Posted on Dec 29, 2007

  • 1 Answer

SOURCE: Casio SPF 40 beeper not working after battery change

There is this little spring which fits in one of the small holes in the watch. When I tested my watch without the spring, there was no beep. With the spring in place the sound worked nice again. So (IMO) apparently the little spring is used as contact between the watch en the "speaker" placed at the back of the watch.

regards,
Pieter

Posted on Dec 21, 2008

  • 2501 Answers

SOURCE: WHEN I GO DIVING HE DOESNT VANT TO SAVE DEPTH INTO

Perhaps you have not instructed it to start recording?

I cannot gain access to the instructions for you watch as the site require me to enter the watch number.

If you have not got the instructions, go to "casio.com", select "support" , then "manuals", then "watches"; agree terms and conditions; select "archive...".

Enter the number off the back of your watch and download instructions.

Posted on Jan 24, 2010

Testimonial: "thank you very much!!"

  • 1 Answer

SOURCE: casio pathfinder SPF 70-s titanium band adjustment

I purchased a Casio Pathfinder solar/atomic watch, with compass, altimeter, barometer, thermometer, model 1200T-7WC (titanium).
Has the titanium band - on this particular band each link is somewhat waveshaped {i.e., there are 2 "arms" from the link making contact with the middle part of the link above (above meaning towards the watch body), and 1 arm fitting between the 2 arms of the next link down). Unlike described in the first solution, the pin is not split, but solid (doesn't look like a slotted screw on 1 end, so the solution at http://www.wikihow.com/Adjust-a-Casio-S-935L-Watch-Band is no help). Here's what to do if you have this band:

1. Note: before you start, be advised there is a tiny loose 1/8" part (sleeve) that will fall out as you pull the links apart, so work over an appropriate surface to "catch" it. Push pin (from the upper "arrow end) of one of the removeable links (those with the arrows on the backside) out of its hole with a fine poker (I used a 1/32" jeweler's screwdriver, an unbent paperclip would also work, just more likely to bend as you push pin out). This takes some force to do - in my case, after pushing, the pin projected out about 1/2 of it's length, I used needle-nosed pliers to gently pull it out the rest of the way). CAREFUL - once pin is removed and you pull the link away from the one above, a small (1/8") constriction sleeve should fall out of the center arm of the link above. SAVE THIS SLEEVE!

2. Using the same procedure, remove the pin from the bottom end of the link you're removing. again, SAVE THE SLEEVE.

3. to rejoin the band once the link is removed, look at the single/middle "arm" of the upper link, looking for the hole where the pin goes through. One side of the hole should be noticeably larger/wider than the other side - this is where you will place the SLEEVE - I used tweezers, or needle-nosed pliers will work - it will drop into hole. Keep this upright so that sleeve doesn't fall out, and slide the 2 arms of the lower link in place around the center arm.

4. Slide the pin you removed into one of the outer link arm holes - I found it easier if I started from below, pushing it into the center arm - it will stop when it reaches that 1/8" constriction sleeve. I set the extruded end on the pin on a magazine (i.e., slightly padded surface) and then pushed the top side of the band down, forcing the pin through the constriction sleeve and up into the upper arm hole, and Voila, your band is reconnected. The sleeve is important (without the sleeve in place, the pin will simply fall back out).

Posted on Mar 07, 2010

  • 1 Answer

SOURCE: I have a casio sport

I had this problem with the Casio 2926 at midnight for many weeks and no matter which buttons I pressed, it carried on.
I solved it on my model, by going into alarm set mode (AL) by toggling button on lower left of watch face. Then using button on lower right, cycle through all (5?) alarm options and also check the tiny screen new the rim at top right of watch face marked with SNZ ALM SIG. If a little black box shows up on this screen, switch off the alarm or snooze, by pressing the button on top right.
Otherwise go to Casio and go through their instructions. The watch is not designed for easy use.

Posted on Nov 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change my Casio wr100m from military time to standard


wr100m is not a model number, but stands for 'Water Resistant (to a depth of) 100 meters'.
The model and module number (4-digit number in a small rectangle) are on the back of the watch case.

Mar 19, 2015 | Casio Watches

1 Answer

Casio sea pathfinder sp60d reset


Hello,
You need to open the watch and cortocircuit 2 points into the watch machine.

TicTacArea.com is Officla Casio Dealer
Casio Watches

Aug 19, 2014 | Casio Sea Pathfinder Triple Sensor SPF-60

2 Answers

I have a casio sport sea pathfinder spf-40 I cannot find my manual and the alarm keeps going off, one at 12 midnight and one at 7.15am and i cant remember how to turn it off please help ? andy


I had this problem with the Casio 2926 at midnight for many weeks and no matter which buttons I pressed, it carried on.
I solved it on my model, by going into alarm set mode (AL) by toggling button on lower left of watch face. Then using button on lower right, cycle through all (5?) alarm options and also check the tiny screen new the rim at top right of watch face marked with SNZ ALM SIG. If a little black box shows up on this screen, switch off the alarm or snooze, by pressing the button on top right.
Otherwise go to Casio and go through their instructions. The watch is not designed for easy use.

Oct 28, 2010 | Casio Sea-Pathfinder SPF40-1V Wrist Watch

1 Answer

How do i set my casio databank to beep every hour


Hello I was in the same problem the last 5 hours causea icant find my owner manual, i put a new battery on my "oldie" but great watch and pusshin and seting i got it....

You have to put in "alarm mode", remember you have to push BOTON MODE. Then you will be at "stand by mode", "data bank(phone) mode", "world time mode", "alarm mode" "chrono mode", and set (analog watch) mode"

then you are in "alarm mode" then push "REV and FWD BOTONS" at the same time, one time, or two times or three times, until the "beep icon and bell icon" are in ON mode

Good look

sareg@hot....

Sep 25, 2010 | Casio Watches

1 Answer

On the casio a158w how do I turn off the hourly chime? Thank-you


Hi Ms. Sophie Desro,

If the alarm has sounded, press "A" (top left-hand button) to stop the sound.
To switch the Daily and Hourly Time Signal on and off:
Press "C" (lower right-hand button) while in alarm mode in sequence:
a. }}}} + BELL = Both alarms on.
b. Display Blank = Both OFF.
c. }}}} = Daily alarm on only.
d. BELL = Hourly Time Signal on only.

Test the alarm by holding down "C" to sound the alarm.
Please note b. and c. to turn off the alarms.

For more information, Casio has an Operational Chart for your watch, Module QW-1275. You may download a PDF file here:
http://ftp.casio.co.jp/pub/world_manual/wat/en/qw1275.pdf

Try this and let me know if this works. Thanks.

Regards, Bill

Sep 16, 2010 | Casio DW290 1V Classic Alarm Chronograph...

1 Answer

I would like to know if the casio 3736 watch is water resistant because I found only the phrase water resistant 5bar


"Water resistant 5 bar" means that it is water resistant to and depth of 50 meters. (1 bar is approximately equal to 10 meters of water depth).

Apr 09, 2010 | Watches

1 Answer

WHEN I GO DIVING HE DOESNT VANT TO SAVE DEPTH INTO


Perhaps you have not instructed it to start recording?

I cannot gain access to the instructions for you watch as the site require me to enter the watch number.

If you have not got the instructions, go to "casio.com", select "support" , then "manuals", then "watches"; agree terms and conditions; select "archive...".

Enter the number off the back of your watch and download instructions.

Jan 24, 2010 | Watches

1 Answer

Casio SPF 40 beeper not working after battery change


There is this little spring which fits in one of the small holes in the watch. When I tested my watch without the spring, there was no beep. With the spring in place the sound worked nice again. So (IMO) apparently the little spring is used as contact between the watch en the "speaker" placed at the back of the watch.

regards,
Pieter

Oct 04, 2008 | Casio PRG-40T-7 Pathfinder

2 Answers

Casio spf 40 Module 2273


Your Watch is in Auto or demo mode. Hold down the "Mode" button for 3 - 5 seconds and it will return to time keeping mode.

Cheers,
Murray

Nov 19, 2007 | Casio PRG-40T-7 Pathfinder

Not finding what you are looking for?
Casio Sea Pathfinder Sports Watch (SPF-60D-7AVDR)- SimplyRun Watch for Men Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Casio Watches Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18429 Answers

Arturs Kalnins
Arturs Kalnins

Level 3 Expert

2338 Answers

Ekse

Level 3 Expert

13434 Answers

Are you a Casio Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...