Andis Logo

Andis Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 158 Products
  • 579 Answers
  • 58K Views

The problem you describe is most likely due to the fact that the machine you bought is designed to operate on 110v/60Hz electrical supply as used in North America. In fact the T-Outliner is only designed to operate on 110v/60Hz so even if you use a transformer you will only convert the voltage from 110v to 230v. You will not convert the frequency 'Hz' from 60Hz to 50Hz which is necessary with an electrical product with many moving parts such as a clipper to operate correctly on the European electrical supply which is 230v/50Hz........Check on ebay 'Voltage and Frequency Converter' about 65 pounds. The only solution

Andis T-Outliner... | Answered on Nov 03, 2014


Voltage & Frequency Converter

Andis T-Outliner... | Answered on Nov 03, 2014


Go to the Andis website and look under the services section, find your clipper model and they will have an exploded view diagram of your clipper with each part listed and directions on where each part goes.

Andis 01690 Hair... | Answered on Oct 23, 2014


Take the upper blade off of the clipper, there will be four (4) screws which secure the adjustable part of the lever to the clipper. You can tighten these screws and that will control how much resistance you get when adjusting the lever.

Andis 01690 Hair... | Answered on Oct 23, 2014


Get a finish nail and stick it in back of the ball pin, hit it with a hammer until it pops out of the other side

Andis Improved... | Answered on Oct 23, 2014


Try Simpsons-online they are Uk main agents

Andis Easy Clip... | Answered on Oct 09, 2014


Make sure the blade is connected to the clipper correctly, if you can pull the blade off without pressing the black release latch then you need to push the blade on further.

Andis Agrc Power... | Answered on Oct 01, 2014


Most common cause will be the blades have gone dull and should be sharpened or replaced. Check that the 2 screws on the blade latch assy are tight where it screws onto the front housing, blade off to check them. 3rd thing to check is for excessive wear in the lever that drives the blades, if it is worn replace it.

Andis Agc Super... | Answered on Sep 30, 2014


Please call the Andis customer service dept at 1-800-558-9441 to purchase any replacement parts for your clipper.

Andis HeadLiner... | Answered on Aug 18, 2014


If the latch has been pushed down without a blade on it you will need to get a flat head screw driver. Push up the blade lock and put the screwdriver behind the the tongue on the hinge. While pushing up on the latch push the tongue out with the screw driver. If you need any add'l assistance please call the Andis customer service dept at 1-800-558-9441.

Andis AGC2 Hair... | Answered on Aug 18, 2014


To purchase replacement parts or schedule repair for your Andis clipper please call our customer service dept at 1-800-558-9441.

Andis Improved... | Answered on Aug 18, 2014


The bottom of the unit screws off to remove the old AA battery and slide in a new one.

Andis NT-1... | Answered on Aug 18, 2014

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Andis Experts

Bruce Showalter

Level 2 Expert

133 Answers

shaveroutlet.com
shaveroutlet.com

Level 3 Expert

1639 Answers

Ross Keen

Level 3 Expert

1351 Answers

Are you an Andis Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...