Air Purifiers - Recent Questions, Troubleshooting & Support


Google (bionaire)(f70s)(manual) without parens.

Bionaire Air... | Answered on Jun 04, 2019


The fuse is located inside the control panel. It is soldered to the circuit board, not mounted in a typical fuse holder. You will need a Philips screwdriver to disassemble the unit. You will need a soldering iron & solder to remove the fuse and replace it. You may want to a multi-meter to check the fuse. If the unit just stopped working, it could be a number of other issues than the fuse. The starter capacitor for the motor could be dead or some other issue. You must take precautions against electrical shock. You may need a technician to safely perform some repairs.

Honeywell Air... | Answered on Jun 04, 2019



I had similar issues and by replacing the 2200 micro (Mu) Farad, 10 Volt capacitor on the PCB, all of my issues ceased.
Below is a link with information supplied by "fixya" that explains the procedure/details.
Hopefully this will solve your current issues.
Good luck,
Mike
http://potlash.org/feast/2010/11/20/repairing-a-jet-afs-1000b/



PS Linda Haus of "Rockler" Technical Support was kind enough to supply me with this link.

Jet AFS-1000B... | Answered on May 25, 2019


check the remote batteries....

Ionic Pro Air... | Answered on May 22, 2019


service manual is not allowed for Avery one....it is only with company service stations.

Shark NV22L... | Answered on May 16, 2019


The disassembly is simple. Remove the four screws you noted at the top of the unit. Each side panel will then slide up about a half inch. Pull outward and they're off. (The bottom is held on by tabs on the unit and slots on the panels). Clean it with a combination of vacuum and compressed air. Wipe the blades down with a mild cleaning detergent. (Spray it on the rag and not on the unit to keep the electronics safe). When re-assembling, be CAREFUL...the two panels are not identical. One has the spot for the light bulb. Carefully replace this panel so as not to break the light. Align both panels well by pushing down so the slots re-engage the tabs, and you're done.

Blueair 501 Air... | Answered on May 07, 2019


The lock symbol means the buttons are locked to stop kids etc or accidentally changing the settings. The owners book should say what to press to unlock it. Most of the time, 1 or 2 of the buttons need to be pressed down for a few seconds to unlock. I have no idea which buttons.

Hunter Air... | Answered on May 03, 2019


It's a bad batch of components in the couple you have gotten. Return it if you haven't already and purchase one elsewhere.

Ionic Pro TURBO... | Answered on Apr 29, 2019


I am having the same issue. I've just replaced the filter and it started leaking out of this hole, where it never had before.
I am thinking that maybe the filter isn't seated properly, and that's causing the leak. But I have attached a picture of the hole in question. Any advice would be helpful. Thanks!



16338748-yk0u0azcqqdkdok2b0oshkdn-1-0.jpg

PUR (FM-9500)... | Answered on Apr 18, 2019


What happens if you hold the button down for 5-10 seconds ?

Air Air... | Answered on Apr 16, 2019


Google IT JUST AS WE COULD

Air Purifiers | Answered on Apr 11, 2019

Not finding what you are looking for?
Air Purifiers Logo

5,226 questions posted

Ask a Question

Usually answered in minutes!

Top Air Purifiers Experts

Marvin
Marvin

Level 3 Expert

85020 Answers

Michael Youngman
Michael Youngman

Level 2 Expert

296 Answers

Brad Brown

Level 3 Expert

18060 Answers

Are you an Air Purifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...