Dishwashers - Page 3 - Recent Questions, Troubleshooting & Support


That usual means water level too high try tilting your dishwasher to one side and some water will spill and then try it again sometime the float in dishwasher is detecting water level too high if that doesn’t you may need the water flow meter that’s a big plastic usual found on the side of the dishwasher

Bosch... | Answered on Jan 14, 2019


I experienced the same problem after my tension cables broke. The door fell open with such force that it bent the hinges a little. If you've replaced the tension strings (which you should do every 5-8 years) then you don't have to replace the latch. I did and it didn't solve the problem.
Here's the solution:
Put a towel at the bottom of each side of the door by the hinge.
Push the door closed a couple of times to bend back the hinges.
Remove the towels and you're back in action.
Good luck

KitchenAid... | Answered on Jan 14, 2019


Fault symptoms point to a burnt out element, which will need to be replaced.

Maytag... | Answered on Jan 14, 2019


uses a cr1620 battery

Mavea 1001125... | Answered on Jan 13, 2019


your drain pump may have failed or is blocked if you can get diagram of your unit find the drain pump they do have video online on how to replace them if you are able to do the work be safe

Dishwashers | Answered on Jan 13, 2019


sounds like your drain hose is bad you need to find where your drain pump is and check the hose for damage.you may be able to get diagram online from manufacturer manual of your model. if you are able to do the work yourself if not find a repair shop be safe

Dishwashers | Answered on Jan 13, 2019


Sounds like the main Circulation Pump is not working correctly. Usually due to the plastic blades in the pump broken / or disintegrated. Replacement pump quite expensive!

Dishwashers | Answered on Jan 13, 2019


I had this problem and discovered it was due to a leak. The float switch attached to the bottom panel was operating. Pull out the mains plug, tip the machine on it's side (water will escape so get a mop ready), remove the bottom panel, 3 screws front and back, disconnect the connector from the float switch. Tape the connecter up out of the way and stand your machine back up. Try running it now. If you have a leak somewhere then you will get a puddle under the machine. If no leak, then I would suspect the float switch itself.

Hotpoint 24 in.... | Answered on Jan 13, 2019


see the video and fix it. God bless you

Dishwashers | Answered on Jan 12, 2019


Is your dishwasher hard wired into the house power system ... or plugged into a wall outlet under the kitchen sink?
You mentioned you turned off the power ... how? via the circuit breaker or disconnecting it from the wall? If your unit is plugged into an outlet (and you depowered by cutting the breaker) ... I would check the cord and outlet .. it might be as simple as that.
If that is not the problem ... trying a reset.
Below is a generic one for Whirpools which may work on your model
To reset it, you will have to have the door open. It can not be latched. Press "Heated Dry," "Normal," "Heated Dry," "Normal" within three seconds of the first pressed button. Now close the door, this should reset your dishwasher.
Good luck on your troubleshooting!

Whirlpool... | Answered on Jan 12, 2019


Reset Procedures for the Fisher & Paykel Dishwasher
  1. Press and hold the button decorated with the key and lock image for five seconds.
  2. Press the power button to turn off power to the Fisher & Paykel dishwasher.
  3. Wait a few minutes and then press the power button to restore power.
  4. Turn off and unplug the dishwasher if the issue remains.

Fisher and... | Answered on Jan 12, 2019


I guess you got the alarm AL 6 on your display what means failure to drain. A control procedure has been added to all the final drain phases in order to check the status of the pressure switch. The contact must be open in the "empty" position in order to ensure that the cycle is performed correctly. If the contact is closed, the drain phase is repeated. At the end of the second drain phase, if the pressure switch contact remains closed, "AL" alarm condition is generated.
Could be following:
  • Domestic drain circuit not suitable (obstructed / blocked)
  • Drain pump jammed
  • Pressure switch faulty
  • Sump - pressure switch tube obstructed
  • Filters / drain hose obstructed
  • Relay or Triac faulty

Down under is from AEG Favorit 86460 user manual, page 30 :

...a flashing fault code appears
an audible signal informs you that an alarm has been activated, in the display appears one of the following flashing alarms: AL1 - AL2 - AL3 - AL4 - AL5 - AL6 - AL7, AL8 and the indicator light of the phase under way is flashing. They are indicative of a fault in the dishwasher that you can probably rectify yourself.
- press the On/Off push button to switch the dishwasher off
- open the door and carry out the following suggested corrective actions.untitled-wdmylhxvjmokugi3zifm2oyn-2-0.jpg

Dado

AEG Dishwashers | Answered on Jan 12, 2019


How to Reset the Control Pannel for a Kenmore Dishwasher Quiet Guard 2
  1. Unlock the dishwasher control panel before resetting it. ...
  2. Press the following sequence of control panel buttons in quick succession: "Heated Dry," "Normal Wash," "Heated Dry" and "Normal Wash."
  3. Allow the dishwasher to perform a brief diagnostic tes

Kenmore... | Answered on Jan 12, 2019


Fault in thermal cutout or heating pause fault. Selected temperature not reached in 90 minutes
?· Check heating element
?· Check thermostat

Dishwashers | Answered on Jan 12, 2019

Not finding what you are looking for?
Dishwashers Logo

89,746 questions posted

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Mike

Level 3 Expert

4356 Answers

Marvin
Marvin

Level 3 Expert

83850 Answers

Brad Brown

Level 3 Expert

17805 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...