Dishwashers - Page 8 - Recent Questions, Troubleshooting & Support


Open the door and look on the side of the door - there are two screws on either side (covered by gray caps usually) - most likely a T15 screw - loosen but do not remove the screws - pull up and the panel will slip free from the door

Miele... | Answered on Mar 03, 2019


The F14 Fault is a heater pressure switch fault - usually a machine that that been in service for a while gets soap build up in and around the sensors - the heater pressure switch being one of those. Its purpose is to measure the pressure of the recirc pump to make sure there is sufficient water pressure to turn the heater on - without sufficient water pressure the heater would burn up. The pressure switch gets gummed up with soap deposits over time and should be changed out

Miele... | Answered on Mar 03, 2019


Depending on the model - take off the toe kick and your will see two screws on either side - one to adjust the rear height and one to adjust the door spring tension

Miele... | Answered on Mar 03, 2019


I have an old GE that did the same thing, if I don't use it enough it will do the same thing. The hum is from the electric motor in the bottom trying to rotate. I don't know your machine but I assume they are all made closely the same. Remove the bottom cover. You should see the back of the motor and it will probably have some slots in the rear cover. Close the door and try to start it while looking through the rear slots. I saw mine turn like an 1/8 inch and stop. The first time it did this, I unplugged a connector feeding the motor, tried to start it to make sure it didn't do anything and then with a long thin screwdriver went to the slots to help turn the motor. The second time I discovered on the right side of the motor housing there was a small opening towards the front of the motor (rear of dishwasher) I was able to get my fingers in there and turn the motor a few times by hand, plug the connector back in and the dishwasher started right up. Seems like the engineers knew this could be a problem and left an access point for us (or dishwasher repairmen to use and charge us $80 or something)

Maytag... | Answered on Mar 03, 2019


Hi
Is this the first time you are operating your dishwasher or if you have already operated it before go for the instruction manual of your machine which could possibly solve your problem.If you don't have the instruction manual don't worry i have attached a PDF of the manual go through it.Hope it solves your problem.If it doesn't i would recommend calling the technician to avoid further problems.If any other issue occurs please reply.Please rate me if my solution helped you.
You could have your instruction manual here.just click on this link.
http://www.dishwasher-manual.com/manuals/hotpoint-ariston/Hotpoint-Ariston_LBF_51.pdf

Regards,
bonefirediv.

Ariston... | Answered on Mar 03, 2019


It looks like GE replaced two components into one new part for the rack slide. Do a search for WDX35X20994

https://www.geapplianceparts.com/store/parts/ModelSectionParts/PDW7800G00BB/3/0/0/0/UPPER_RACK_ASSEMBLY

GE 24 in.... | Answered on Mar 03, 2019


I'm pretty sure the "air hose" is the drain hose from the dishwasher and is supposed to empty in the garbage disposal. Garbage disposals are made for this optional hook up with a plug you have to knock out and remove from the inside of the disposal. If you run the dishwater with the hose not connected to disposal it has to be going somewhere!

GE Nautilus 24"... | Answered on Mar 02, 2019


Switch off and unplug the washer.
- Check the fill hose isn't blocked, squashed or kinked.

Blomberg... | Answered on Mar 02, 2019

Not finding what you are looking for?
Dishwashers Logo

90,067 questions posted

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Mike

Level 3 Expert

4356 Answers

Marvin
Marvin

Level 3 Expert

84027 Answers

Brad Brown

Level 3 Expert

18002 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...