Dryers - Recent Questions, Troubleshooting & Support


If the diameter is 6, the circumference is 6 times pi or 18.85. The counterweight will lift 18.85 for each single rotation of the drum

Dryers | Answered 18 minutes ago


Locating the Thermal Fuse
In GE dryers, the thermal fuse--sometimes called a safety thermostat--is located behind the drum on the inside of the dryer. ... Look inside the dryer, behind the drum, to find what looks like a round metal pan. This metal pan is actually the dryer's heating element housing.

GE Dryers | Answered 4 hours ago


I did A & B, B actually did the trick and I have had absolutely no problems.

Possible Solutions
A
Power unit down by turning off the circuit breaker(s) for one (1) minute.
  1. Power unit up by turning on the circuit breaker(s).
  2. Start a time dry cycle.
  3. Monitor the dryer for one (1) minute to ensure the error code does not display again.
B
It indicates that the lint screen or vent is clogged; the vent is crushed, kinked or has too many turns. ... The dryer will continue to run when this diagnostic code is present.

My dryer did the same thing. I cleaned all the vents thoroughly, if you are unable to clean inside where the vent screen is try this. remove lint screen, using tape or rubberband attach a empty paper towel roll to the end of your vacuum crevice tool. Also at the 99 cent store I purchased a appliance brush to loosen any lint inside before vacuuming. The brush works better then the one I purchased from Home Depot for $15.
Vacuum the inside of the dryer, be sure to vacuum the very back inside and around the door.
This is the tricky part now.
The dryer flex hose actually has to be set just right. If the placement is incorrect you will get the error codes, dryer turns off after mins etc.

Here is a Flex hose tip video. Hope this is helpful

Maytag Dryers | Answered 4 hours ago


I had the same problem. Turns out the reset button on the back of the dryer needs to be pushed; when you push the reset button you should hear a click. If you do not hear a click the problem was probably not the reset button. The button shuts down the dryer heating elements if they are getting too hot and also keeps the drum from turning unless the start button is held down.

If you push the reset button and the dryer starts to work again, I strongly recommend that you stop the dryer and investigate why the heater elements overheated. In my case there was lint/hair build up on the heater elements themselves. Extensive dryer disassembly is required to properly clean the heating elements but it is worth the prevention of a house fire. While you're at it, clean the rest of the machine and the duct work.

Hope this helps

Asko T700... | Answered 11 hours ago


Some dryers have a switch that opens when a belt breaks to stop motor operation.

GE Dryers | Answered Yesterday


I have an electrolux electical dryer t3350 gave the error E 08

Electrolux... | Answered 2 days ago


Some LED lamps cannot be dimmed. You may have the wrong type. Also incandescent lamps and LED lamps are not interchangeable.

Dryers | Answered 2 days ago


It could be a blown fuse or the heating element may be burned out.

Dryers | Answered 2 days ago


Have you tried unplugging it for a minute or so?

Samsung Dryers | Answered 2 days ago


Whether the fan has a dedicated oscillation motor or is driven by an extended shaft from the main motor, there is usually a button or switch to disengage the oscillating function. If this no longer has any effect the only cure is to dismantle the machine until the fault is discovered and then if a repair is possible - repair it...

Most domestic fans have no spare part support, mechanisms have a limited life and if "handyman" repairs aren't possible it is considered a throw-away item.

Lakewood Dryers | Answered 2 days ago


E 5 Usually means open fuse. Usually a secondary fuse behind the cover where the Blower is. If you change the fuse and still have no power you have a wire issue. Could be a loose connection, or a wiring shorting out somewhere.
Let's hope the fuse takes care of it. Be sure to unplug it before. Checking anything. 220 volt will hurt you. Hope this helps you..

Amana Dryers | Answered 3 days ago


fixya is not a chat group. Google it.

Dryers | Answered 3 days ago


Possibly someone at Home Depot or Lowes would know, but unknown if that model has another name particularly for Hampton Bay fans. Maybe it is a Westinghouse fan, which I understand purchased Encon, but may not have support manuals for it.


If it is a Monte Carlo fan, below is an example of results of a search using http://w.google.com

(That is how to "Google" something.)


http://www.montecarlo-ceilingfans.com/support/monte-carlo-ceiling-fan-manuals/ "> http://www.montecarlo-ceilingfans.com/support/monte-carlo-ceiling-fan-manuals/

Dryers | Answered 3 days ago

Not finding what you are looking for?
Dryers Logo

116,664 questions posted

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Brad Brown

Level 3 Expert

18072 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...