Office Equipment & Supplies - Page 7 - Recent Questions, Troubleshooting & Support

Can you feel any physical heat from the fuser. Sounds like either the thermistor that controls temperature or the lamp failed.

Xerox Office... | Answered Yesterday

COF32 means the ATDC sensor has detected some unusually high or low readings.
The ATDC sensor measure the toner lever inside the developer unit.
Try swithcing on/off, open/close the front door to clear the code.
If this doesn't work, you'll need an engineer to reset the ATDC level.

Good luck


Konica Minolta... | Answered Yesterday

  1. Go to this code with "Clear Mode"+107+"Clear/Stop" hold for 5s.
  2. Go to System Settings
  3. Go to 5875
  4. Check the setting of SP5875-001. If the setting is set to "1 (OFF)",change it to "0 (OFF)".
Try checking or changing the thermistors!
The metal contact spring on the thermistor broken causing all sorts of 'unrelated errors including 'Please Wait' sc 670 and sc 402...

Ricoh Aficio 450... | Answered Yesterday

You do know you can google your question for answer, try it.\It took less than i second to find answer. Here is a big hint

The Office... | Answered Yesterday

Error code 122 means " Low voltage FAN error ".

Is the FAN (bottom right of the front) of the low voltage power supply block working? Is the FAN connector connected correctly?

Check to make sure connection of the FAN connector. Replace the low voltage power supply unit. Replace the FAN motor. Replace the low voltage power supply unit.


OKI Office... | Answered Yesterday

I have a 2 year old Summuit photofix and have recently got a new computer with Widows 7. The Summit won't work.

Any ideas.


Office Equipment... | Answered Yesterday

Probably a new drum is required.

Canon Office... | Answered Yesterday

The message 'No Waste toner box' indicates the belt unit is not installed properly. To verify the belt unit is installed properly, follow the steps on this link:

If the problem continues, the printer may need service. The printer has a one year limited on-site warranty. If the printer is in warranty, call Brother Customer Service at 1-877-Brother (1-877-276-8437) for warranty options.

If the printer is out of warranty, contact a Brother Authorized Service Center for repair by clicking on the link below:

Brother Office... | Answered Yesterday

This is just a shot in the dark, but if there is no "reset" button, you might try unplugging it for a couple of minutes and it should reset itself to factory default settings. Just a guess. If you have an owners manual, I would check there to find how to solve the problemt. You will want to enter the "menu" if there is one, and discover whether you can turn solve the problem there. If you don't have an owner's manual, you might be able to find one at the printer manufacturer's website in the support section.

Konica Minolta... | Answered Yesterday

First you have to find out where the paper jam occurs. Check the Rollers and the clutches, then the sensor for the registration and finally the exit sensor. Clean or replace any defective part.

Kyocera Office... | Answered Yesterday

10871087, type 004 and press Start. Choose Execute and press again Start. Restart then the device.

Kyocera Office... | Answered Yesterday

As I know you cannot enter in Service Mode like the MFPs. Only in the Service Settings in Adjust/Maintenance menu.

Kyocera Office... | Answered Yesterday

Try to clean the mirrors in the scanner unit.

Kyocera Office... | Answered Yesterday

You can read the manual for the device and the command center in order to setup the Scan to SMB.

Kyocera Office... | Answered Yesterday

Not finding what you are looking for?
Office Equipment & Supplies Logo

591,566 questions posted

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts


Level 3 Expert

8081 Answers

Cindy Wells

Level 3 Expert

5909 Answers


Level 3 Expert

84966 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides