Water Heaters - Recent Questions, Troubleshooting & Support


Try mounting on rubber standoffs. The mechanical timers are noisy and when mounted on a wall that amplifies the noisy.

As a test, un bolt it from the wall and see if noise is acceptable. If so, find a cushioned mount.

Intermatic WH40... | Answered Yesterday


make sure the water supply linee is on,and water outlet line is open.,and unit is plugged in.
If all are...u got a bad unit.

Water Water... | Answered Yesterday


The problem might be fixed by removing the cartridge and cleaning it thourghly and resetting temp stop.Yes the cartridge could be bad but new parts are readily available. Depending on water quality conditions in you area it may be difficult to disassemble so it may be a good idea to have a plumber do it for you. Thank you.

Grohe Grohmix... | Answered 2 days ago


I wonder if you have this problem below caused by a drop in water pressure from someone flushing a toilet or a washing machine. I would call the company to remedy this issue.

17. What is a cold water sandwich effect? The term “cold water sandwich effect” is a term that is used to describe the introduction of cold water into the hot water supply line during frequent on/off operation of an instantaneous water heater. The cold water sandwich effect, when present, appears as a momentary drop in hot water temperature as it is discharged from a hot water supply outlet (i.e. shower, tub, or faucet). This phenomenon is present in the operation of all instantaneous, tankless style, water heaters, but is minimized with the high tech design of Rinnai water heaters.
The technology built into the Rinnai water heaters is designed to minimize the cold water sandwich effect. Rinnai water heaters are microprocessor controlled and when water flow through them ceases, they remain in a “ready to fire state” for approximately 1 minute. If water flow through a Rinnai water heater begins within the first minute following water flow stoppage, the water heater will fire back up within 1 to 2 seconds. This minimizes the cold water sandwich effect that would otherwise be experienced with a low tech tankless water heater. It should be noted that the cold water sandwich effect cannot be removed completely from tankless style water heaters. The safety standards developed to insure the safe operation of water heaters require a delay in the ignition sequence of all gas water heaters.
While the cold water sandwich effect cannot be completely eliminated from standard plumbing systems, it can be eliminated from plumbing systems that have a supply and return hot water circulating system. Rinnai has developed 2 methods to eliminate the cold water sandwich effect in residential hot water circulating systems.
The first (and preferred) method to remove the cold water sandwich from circulating systems utilizes a small electric tank water heater (powered up) that is used with a dual purpose. The small water heater acts as a mixing tank to eliminate the cold water sandwich effect from the Rinnai water heater and it uses its electric heating element to offset the heat losses from the hot water circulating system.
The second method to remove the cold water sandwich from circulating systems utilizes a small 2 to 6 gallon storage tank installed on the hot water outlet of the Rinnai water heater. This tank acts as a mixing tank to blend the cold water sandwich with hot water and eliminating its effect at fixtures.

Rinnai Water... | Answered 3 days ago


check the pressure control that switches the element on or off
if it is faulty then it switches on when the tap is turned on dropping the pressure but it will not recognize that the increase in pressure when the tap is turned off so it keeps heating the water.

Stiebel Eltron... | Answered on Jan 13, 2019


It does that with weak batteries - try replacing with fresh batteries.

Water Heaters | Answered on Jan 11, 2019


sadly WE CAN NOT IT NEEDS A PROFESSIONAL REPAIR SERVICE

Water Heaters | Answered on Jan 10, 2019


You will need a ht return line which is feed into bottom of heater via pump. ensure that you install 2 block valves , one before and 1 after pump. Install a check valve between the discharge of pump and block vale. Why did you not by a recirculation pump that is designed to installed at heater. You can replace pump by removing it using 2 bolts?

Water Water... | Answered on Jan 07, 2019

Not finding what you are looking for?
Water Heaters Logo

17,353 questions posted

Ask a Question

Usually answered in minutes!

Top Water Heaters Experts

Donni Steen

Level 3 Expert

687 Answers

Brad Brown

Level 3 Expert

17804 Answers

Paul Carew

Level 3 Expert

3411 Answers

Are you a Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...