Cobra Logo

Cobra Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 854 Products
  • 26K Answers
  • 674K Views

don't they come with coax and antennas already installed? If you can run the coax out the window to the mirror bracket then up and over the visorsthat would be good.the only thing is if it has a fiberglass door,no ground plane. you will have to then ground the antennas to the chassis and maybe even use a grounding strap.

Cobra 29 WX NW... | Answered on Oct 10, 2019


It means either the knob or something in the squelch circuit has gone bad. Doesn't mean that you cannot use the radio, you will just hear static all the time when no one is talking. If the static bothers you, you can always back the RF gain down a bit. That will quiet the noise, but lower you receive range. meaning you won't hear as far away.

Cobra 19 DX IV... | Answered on Oct 07, 2019


That's a confusing question. Device id is the FCC device ID number and means it has been approved to transmit in the USA. It has nothing to do with model. So, in terms of a radio device, it means nothing to a tech or a way to get parts or even a battery. The device ID is typically located on the back of a radio or under the battery. Could you ask what you are looking for?

Cobra Radio... | Answered on Oct 04, 2019


Hi Anonymous, as you say, your batteries have little or almost no charge capacity
That's why the charger lights remain on
Simply replace the batteries.
I hope you can solve the problem
Greetings Franco Dosil

Hola Anonimo, por lo que comentas, tus baterias tienen poca o casi nula, capacidad de carga
Espor eso las luces del cargador permanecen prendidas
Simplemente, reemplaza las pilas
Espero puedas resolver el problema
Saludos Franco Dosil

https://fccid.io/BBOLI4900/User-Manual/USERS-MANUAL-751014

Cobra Radio... | Answered on Sep 26, 2019


the issue is that this radio has an audio boost control function, Dynamike. That is likely the issue, the two are working against each other. You can see if the power mic you have will work if you dial the Dynamike all the way down, but you might have to live with the stock mike.

Cobra Radio... | Answered on Sep 24, 2019


trying to update my cobra 5600 pro lm gps

Cobra GPS | Answered on Sep 16, 2019


Check you user manual and see if it has a procedure to do a factory reset as typically this is the only way to get things like this working again.

Cobra Computers... | Answered on Sep 14, 2019


as far as i know radar is radar it all works on band width
i would think you should be find cobra can answer you 773-889-3087

12-Band... | Answered on Sep 13, 2019


What is the swr? This can impact the receiver. However, the tuning coils for receive and transmit are close to each other and someone most likely turned the receive coil instead of the transmit coil. The coils that are adjustable that affect receive are 13, 15 and 3. 3 is the coil that is close to the transmit section. You may want to have it realigned.

Cobra Radio... | Answered on Sep 13, 2019


OLP or Over Load Protection means the device plugged into the inverter is over loading the the inverter please ensure the device you have plugged in is not rated to more than 2500w of power.

Cobra... | Answered on Sep 07, 2019


If it "keys up" without a mic plugged in, try plugging the mic into the radio and see if it stops. Some radios require the mic to be plugged into it to operate properly. If it is keyed up with the mic plugged into it, try unplugging the mic and see if it stops. If it does stop when you unplug the mic, either the switch in the mic is stuck/went bad or there is a wire shorted in the mic cord to radio plug. Make sure pins 3 and 4 on the mic plug are not shorted. A continuity meter will tell you. If the mic is keyed, pins 3 and 4 will show a short, if the mic is not keyed, pins 3 and 4 should not show a short. If the mic is functioning normally but the radio is still keyed up then there is something in the radio that is shorted.

Cobra Radio... | Answered on Aug 29, 2019


pull the batteries out, slam them ******* a solid surface. put 'em in, let 'em charge. if that doesn't bring 'em back buy new bats.also, use a voltmeter to make sure the charger was getting voltage.
Good luck!

Cobra Microtalk... | Answered on Aug 26, 2019


Use scissors? .... please explain what you mean.

Cobra Radio... | Answered on Aug 25, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Cobra Experts

Brad Brown

Level 3 Expert

18108 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

The Knight
The Knight

Level 3 Expert

76140 Answers

Are you a Cobra Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...