Frigidaire Logo

Frigidaire Recent Questions, Troubleshooting Help & Support

  • 3K Products
  • 135K Answers
  • 3M Views

The LED above the Ice Off icon should be lit when the icemaker is disabled. It should be off when you want ice from the icemaker. To toggle the setting, press and hold the Ice Off touch pad for 3+ seconds. This is shown in the manual for the FPHF2399MF2 on page 14. Sears Parts Direct has the manual here: https://www.searspartsdirect.com/manual/234cu4elin-001428/frigidaire-fphf2399mf2-bottom-mount-refrigerator .

I hope this helps.

Cindy Wells

Frigidaire... | Answered 1 hour ago


Spider arms attached to stainless steel drum inside of tub have probably broken. This is a known problem with Frigidaire front loading washing machines. The stainless steel drum has a 25 year warranty but this does not include the spider arms. You cannot buy the spider arms separately, you have to buy the unit as one. The drum cost about $250.00 and probably about $300.00 in labor to install. You can do it yourself but it is pretty involved. Good Luck!

Frigidaire... | Answered on Oct 09, 2019


Possibly, the replacement EOC is defective.

Frigidaire Ovens | Answered on Oct 06, 2019


first try moving your drain hose higher it can cause this problem

Frigidaire... | Answered on Oct 04, 2019


If new and under warranty contact supplier. If you attempt to fix while under warranty and cause further faults then you may void warranty.

Frigidaire... | Answered on Oct 03, 2019


i don't know. be careful with electricity. if possible, try running normal washer load along with your dryer but with [no heat] 'cold air only' to see if they will keep running.
if they run OK, consider shutting off both washer and dryer. shut off main electrical panel and change fuses for both washer and dryer. turn hydro on and run both again
with your normal settings. if they fail again please call for repairs. my dryer would not run and although everything looked and tested out OK, i had to replace a small 6x8"
electrical box having 2 only 30 amp screw in fuses.
then it ran OK.

Frigidaire... | Answered on Oct 02, 2019


I had this same issue. My dryer would run and heat up but then stop and give me the f40. I measured all thermisters and everything was in range. The tech sheet stated that I needed to buy a new control board and I did. Same problem.
The solution was a loose connection on for p4. I took needle nose pliers and squeezed the connector to make it fit tight on the board and everything is working now.
Bottom line, expensive dryer with cheap connectors.

Frigidaire... | Answered on Sep 30, 2019


Hi- not sure if it will help but I had issues getting it out. What I found is the plastic casing (fridge) needed a little twist/push. Play with it- hold the filter in and GENTLY push/pull/twist slightly the fridge housing.

Frigidaire... | Answered on Sep 29, 2019


Cannot be answered with the information provided.

Need the serial number from the manufacturer's plate, which will probably tell you the year of manufacture.

Here is a link to Frigidaire: https://www.frigidaire.com/Owner-Center/Product-Support--Manuals/?productCode=FFBD2406NB

Frigidaire... | Answered on Sep 29, 2019

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Frigidaire Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18108 Answers

Cindy Wells

Level 3 Expert

6031 Answers

Are you a Frigidaire Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...