Kyocera FS - Recent Questions, Troubleshooting & Support

F248 is communication problem ,it some times happens when the printer cannot understand the data coming from the computer from certain program's or a specific file .reset the printer clear any print jobs on the pc and try print a test page if you're still getting that error you will need to get a service engineer to upgrade to the latest firmwarec

Kyocera... | Answered on Jun 27, 2019

Error Code 6000 is fuser code, you need to replace the fuser unit, make sure there is no paper stucking there first!

I’m happy to help further over the phone at

Kyocera FS-2000D... | Answered on Jun 18, 2019

make sure dial on front of cassette matches paper size in cassette

Kyocera... | Answered on Jun 13, 2019

LSU cleaning motor error

When the LSU cleaning motor

is driven, an error signal is

detected continuously for 1 s.

Defective connector

cable or poor

contact in the connector.

Reinsert the connector. Also check for continuity

of the connector cable. If none, replace

the cable.

Kyocera... | Answered on May 27, 2019

Can you be more specific or provide error codes or messages?

Kyocera... | Answered on May 05, 2019

In some cases you can reset the C 6000 - when is a false error.
try this:
1. Go to Menu/System and browse till you see
press and hold: # START ENTER
The "Service" will go away and browse to "Maintenance".
2. Press ENTER to go in maintenace mode - the display change to Maintenance mode.
3. browse to 0163 and press ENTER - reset fuser
4. pick EXECUTE and press ENTER
5. turn the copier OFF, wait 20 seconds and power up the machine.
If C 6000 goes away it was a false error if NO ...try again and if the C6000 persist means the thermal fuse it is blown so you have to replace the fuse = call for service.

Kyocera... | Answered on Apr 10, 2019

there are many many factory modifications/bulletins for that machine, really the tru fix is very time consuming and if you are paying a dealership to repair, it will cost you more than machines value

Kyocera... | Answered on Apr 08, 2019

F000 is a panel communication error... update firmware... firmware as far as i know isnt available to the public... contact kyocera

Kyocera FS-2000D... | Answered on Mar 06, 2019

It is calling for a maintenance kit.

Kyocera FS-2000D... | Answered on Feb 26, 2019

After removing paper tray, above the paper tray slot, on the bottom of unit, left side, is a green tab. Pull metal flap down, remove paper, and your in business. That is just my experience with my friends unit.

Kyocera FS4020DN... | Answered on Feb 01, 2019

The message you get is from the fuser setting for printing envelope. At the back of the printer, you have a handle wich opens the back dor. There is located the fuser (fixing unit) that will slide back. On left and right of the fuser, you can see 2 green buttons. In your case one of them or both are pressed. If you press one time, the button goes down. If you press again, the buton rise up. Try to press them down.

Kyocera FS2020D... | Answered on Jan 21, 2019

call 239 939 5383 they can try to locate one for you and quote you a price for a new one

Kyocera FS-920... | Answered on Jan 03, 2019

MP tray is not the cassette it this flap that pulls down above it.

The machine will revert to asking to place paper in its MP tray when the information it is receiving about the document from whatever program tell it that the size is not the same as what the cassette is set to...

so, check page size in of document in word program or whatever you are using

also check paper type and size settings match those you just checked in the printers properties under printers in control panel.

If you put a piece of paper in the MANUAL BYPASS TRAY bot the cassette it will print on that.

To get evverything back to normal, turn off printer, delete jobs in print que, change paper size of document in word/excell/etc is set same as paper type in printer, print again.. all should be good...

p.s. these are good quality printers that why I bother to answer you... cheers

Kyocera FS-2000D... | Answered on Nov 28, 2018

push the drum unit in completely

Kyocera... | Answered on Nov 08, 2018

replace fuser unit

Kyocera... | Answered on Nov 08, 2018

I had the same problem. Pull the Fuser and check Conector.Sometime pieces of paper inside the Conector raises an error.

Please Rate .

Kyocera FS-2000D... | Answered on Sep 28, 2018

Looking to get rid of 'Install MK' message - any way that i can reset so i dont have to purchase a main kit?

Kyocera FS2020D... | Answered on Sep 20, 2018

Not finding what you are looking for?

-678 questions posted

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts


Level 3 Expert

85108 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers


Level 3 Expert

904 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Kyocera Office Equipment & Supplies

  • Forum

View Most Popular

  • Kyocera Office Equipment & Supplies