LG Washing Machines - Answered Questions & Fixed Issues

If your getting water coming out. Your pump is not working or is clogged with a coin check the hose. And have a shop vac ready to suck up the water. The door has a lock and should not open on front loaders till the cycle is complete and water is drained

LG Washing... | Answered on Aug 16, 2019 | 64 views

Hi from retired Englishman in SW France,

'de' does stand for Door Error. There is likely to be a problem with either the lid/door solenoid/lock or the 'lid/door closed' sensor becoming apparent with the extra movement of washing requiring a service engineer's attention I suggest ;-0(

If this has assisted and/or clarified the situation for you please consider a 4 thumbs up on our rating.
Thanks and good luck!
John C

LG Washing... | Answered on Aug 15, 2019 | 1,001 views

Could be the water valve

LG Washing... | Answered on Jul 22, 2019 | 29 views

Most likely it is a broken 'spider'. That's the 3 armed part that holds the inner drum to the hub. Not uncommon. Can be expensive to fix. Can be done yourself. Check out videos on YouTube or repairclinic or appliancepartspros.

LG Washing... | Answered on Jul 21, 2019 | 39 views

Most top load washers have snap clips in front and hinges in back. You use a putty knife or equivalent to push in the clips(located between top and front of unit in the seem). Some others have screws on bottom near the legs that you unscrew and tilt front forward and then lift up and off. Good luck.

LG Washing... | Answered on Jul 20, 2019 | 35 views

PE= pressure error. A water level error. Check hose to pressure sensor. Is it connected? Does it have a hole in it? Otherwise replace pressure sensor.

LG Washing... | Answered on Jul 17, 2019 | 33 views

Take top off, take control panel off, remove front panel.

LG Washing... | Answered on Jul 23, 2019 | 550 views

It could be damaged or worn bearings. It can also be a broken spider. The spider attaches to the inner drum and is part of the spindle assembly.

LG WD-80130F | Answered on Jul 12, 2019 | 35 views

I'm sure you double checked, but I have forgotten to plug the connectors from the control back together before putting the top back on. Seems obvious but I've done it more than once. Good luck. (And make sure your house breaker isn't tripped)

LG Washing... | Answered on Jul 08, 2019 | 30 views

If this is a front loader and older model check the spider arm on the back of the drum it may be corroded and putting the drum off center at low speed. I just replaced the drum to tub gasket and the spider arm which was severely corroded (name may not be correct go to the LG parts site)

LG Washing... | Answered on Jul 02, 2019 | 772 views

I just finish repairing my LG front loader and this sounds like the same issue. The back of the drum has a spider arm and spindle arrangement (think that the name) the spider are was corroded and broke after 10 years, this puts the drum off balance and chews up the gasket. I had to also repair the wash tub where the drum had worn into it and JB Weld worked fine. It all seem to work fine now.

LG Washing... | Answered on Jul 01, 2019 | 289 views

DL is indeed a door lock error. The code is generated when the CCU can't lock the door. Possible causes are door latch mechanism, connecting wiring, or the CCU. You could hear clicking from the CCU machine which indicated to me the CCU was trying to lock the door. It tries 6 times before setting the F/DL code.
?Check Door Lock/Switch Assembly for foreign objects
?Check Wire Harness connections to the Door Lock/Switch Assembly

All the best !

LG Washing... | Answered on Jun 30, 2019 | 36 views

CL is child lock. Hold child lock button for 3 seconds to unlock

LG Washing... | Answered on Jun 28, 2019 | 34 views

Try turning the water pressure down. If you have high water pressure the water comes into the dispenser to hard and splashes over the front & side of the dispenser draw the trickles down the inside of the front panel out on to the floor. Very common front loader problem.

LG WM0642H Front... | Answered on Jun 28, 2019 | 619 views

could be lid switch are some else, you should call techicain to help you out

LG Washing... | Answered on Jun 24, 2019 | 39 views

Possibly the circuit breaker failed and cannot be reset.

LG Washing... | Answered on Jun 23, 2019 | 957 views

Not finding what you are looking for?
LG Logo

Family Lines

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers


Level 3 Expert

85160 Answers


Level 3 Expert

411 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides