Russell Hobbs Logo

Russell Hobbs Answered Questions & Fixed Issues

Do you work here? Claim your company

  • 237 Products
  • 1K Answers
  • 105K Views

Heating element, thermal fuse, or control circuit failure

Russell Hobbs... | Answered on Jun 30, 2019 | 219 views


Fixya does not sell Russell Hobbs parts.

Russell Hobbs... | Answered on May 27, 2019 | 47 views


Prabable the pump or faulty hoses. Get a pump online, the last one I bought was $35.00 and about 4 hours work ie, setup, takedown and reassembly and cleanup.

Russell Hobbs... | Answered on Apr 28, 2019 | 41 views


You'll probably have to that switch from Russell Hobbs. Here's the link to their service & support. https://www.russell-hobbs.com/parts.shtml

Russell Hobbs... | Answered on Mar 31, 2019 | 75 views


Your faithful servant is facing retirement.

Russell Hobbs... | Answered on Mar 29, 2019 | 39 views


CONTACT RUSSEL HOBBS COMPANY

Russell Hobbs... | Answered on Jul 01, 2019 | 130 views


To disassemble the Russell Hobbs 15081 steam glide iron, you have to remove the two hidden screws on the handle. To locate the first screw remove the two adjacent blue buttons which are each held in with two hidden clips front and rear, so lever out with small screwdriver or similar. The second hidden screw is under the pivots of the water inlet lid.(I broke one of the plastic pivots but no big deal). Then using a thin blade, separate the top half of the handle from the bottom half of the handle. A bit of force is needed as there are more plastic clips. I started from the rear.
Once the top half the handle is removed, other screws become visible, so teardown is not hard, just note which screws go where, as they are different lengths.
My problem was that some of the screws/bolts were so corroded I needed to drill them out. The thermostat was also corroded, which probably explained why the thermal fuse had blown. The element was fine.

Russell Hobbs... | Answered on Mar 04, 2019 | 840 views


To disassemble the Russell Hobbs 15081steam glide iron, you have to remove the two hidden screws on the handle. To locate the first screw remove the two adjacent blue buttons which are each held in with two hidden clips front and rear, so lever out with small screwdriver or similar. The second hidden screw is under the pivots of the water inlet lid.(I broke one of the plastic pivots but no big deal). Then using a thin blade, separate the top half of the handle from the bottom half of the handle. A bit of force is needed as there are more plastic clips. I started from the rear.
Once the top half the handle is removed, other screws become visible, so teardown is not hard, just note which screws go where, as they are different lengths.
My problem was that some of the screws/bolts were so corroded I needed to drill them out. The thermostat was also corroded, which probably explained why the thermal fuse had blown. The element was fine.

Russell Hobbs... | Answered on Mar 04, 2019 | 116 views


Wattage may very with the power used for microwave.

Russell Hobbs... | Answered on Mar 04, 2019 | 46 views


YOU CHUCK IT IN THE BIN AND REPLACE IT WITH NEW

Russell Hobbs... | Answered on Feb 15, 2019 | 83 views

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Russell Hobbs Experts

ray gallant
ray gallant

Level 3 Expert

64223 Answers

Tom Chichester

Level 3 Expert

54158 Answers

JonSnell Electronic
JonSnell Electronic

Level 3 Expert

30501 Answers

Are you a Russell Hobbs Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...