Samsung Dishwashers - Page 2 - Recent Questions, Troubleshooting & Support

At one of the sites, it is said that this error means leakage. But there is no more information about it. Check or at the bottom of the dishwasher there is no water. Maybe you are lucky.

Samsung... | Answered on Apr 13, 2019

Check the heating element of your system. Most likely it was the reason.

Samsung... | Answered on Apr 12, 2019

See if voltage past switch if ok check voltage past transformer

Samsung... | Answered on Apr 10, 2019

Depends on the problem. You can download the manual and "File/Save As" to your Documents folder from here...

Samsung... | Answered on Apr 04, 2019

If the latch is adjustable, adjust it. If that doesn’t work, replace latch

Samsung... | Answered on Mar 13, 2019


Samsung... | Answered on Mar 10, 2019

Probably burnt out water heater.

Samsung... | Answered on Feb 19, 2019

Make sure disposal is working. Also you might have the child lock on.

Samsung... | Answered on Feb 08, 2019

5E code. If your dishwasher has been running fine for awhile then throws a 5E code chances are it could be the pump or a blocked hose or filter but chances are its not. 1. Does the code come on after it has gone through the wash cycle and released the soap dispenser? or 2. Does the code show afer 1 or 10 minutes of running without the wash cycle completing, soap dispenser still closed?
Number 1 is easy to check just diconnect the drain hose and run the hose into a bucket to see if the hose or filter is clogged or pump is working. These machines only use about 2 gallons of water and the pressure is very low its easy to do in a bucket. If number 2 occurs, its not a clogged hose or filter or pump issue the machine is not even cycling.
If number 1 checks out ok you have water flow but shuts down and number 2 has occured, its your Case Level Sensor its the electronic solid state float, DD94-01006A its either sticking due to water impurities or its bad.
Its actually pretty easy to trouble shoot or fix. You have two choices but the machine has to come out. The sensor is located behind a metal plate on the lower left side ofthe machine. You can;t miss it it looks like a float, has a black float inside a clear plastic housing and some wires going to it. You can pull it out and clean it (The float should go up and down with no sticking at all). Or just buy a new one $35.00ish and put in. Also check the inlet hose to the float make sure its clear and clean DD67-0057A.
There is one catch to this that can cause lots of grief if ANY water at all comes out of the float while changing it. If any water gets in the bottom of the catch basin underneath, the very very sentive probes will detct it and throw a LE code and the washer will not work. that is not a big deal just need to pull the basin off and dry it out. The smallest amount of water can cause the sensors to react since its a protection system.
Samsung dishwashers are very quite and wash extremely well but there technology and engineering sucks along with their warrenty and repair manuals there are no manuals for the home owner or much for the repair guy.
That float will have problems again and again and again either its dirty or broken and will cause another 5E code situation.
Side note; food grinders in a dishasher are stupid! All dishes places in a dishwasher should be rinsed! A domestic dishwasher should not be used as a disposal. It makes your house stink and tons of bad bacteriea will grow in places you do not want it to, not to mention they are not made to work like you would think.
Best dishwasher with the least trouble, easy to fix, easy to dignose, easy to work on, good manuals, few problems, good warrenty, best built, quite running, washes great, very well engineered is BOSCH.

Samsung 24 in.... | Answered on Jan 23, 2019

Check there is no debris sticking to the seal and the seal is not damaged.

Samsung... | Answered on Jan 18, 2019

Other blinking lights or beeping sounds may indicate a problem with thedishwasher caused by power surges. ... If the problem persists, reset (reboot) thedishwasher by turning off power to the unit at the house circuit breaker/fuse box for 30 seconds. Restore power and the dishwasher should function normally

Samsung... | Answered on Jan 12, 2019

If the reset does not work after removing power from the dishwasher, then the next thing to try is to press the Start or Reset button to reset the dishwasher. Press for about 10 seconds.

Samsung... | Answered on Jan 12, 2019

Samsung doesn't list your code.
CODES When they occur Symptom POSSIBLE CAUSES 4E Flow-meter in air-breaker don't
detect proper pulse counts in water filling period. (about 237 pulse per 1 liter) In water-fill period, it can't
detect proper flow-meter
pulse counts for 4 minute. 1. Water tap is closed or water intake is restricted.
2. Water pressure is too low.
3. Water inlet valve or Flow-meter is not working.
4. Drain-pump is not working. (Water pressure SW detect high level. so, can not fill any more water.) HE In any mode, Heater is not working. In Heater operation step,
- Do not reach to required
temp. for 60 minutes. 1. Heater or temperature sensor is breakdown.
2. Water in Tub is too low on Heater operation step.
3. Low level Protect device is not working. LE During power-on, the leakage sensor switch is kept ON for 2 seconds. (Have priority over other errors ) Floater in leakage sensor
Press the micro switch. 1. Overfilled into the dishwasher.
2. Leak from somewhere to bottom tray. tE In any mode, short/open circuit
of thermistor is detected. Short/Open circuit or break of temperature sensor.

Samsung... | Answered on Jan 12, 2019

Not finding what you are looking for?
Samsung Logo

1,335 questions posted

Ask a Question

Usually answered in minutes!

Top Samsung Dishwashers Experts


Level 3 Expert

1234 Answers


Level 3 Expert

3042 Answers

Cindy Wells

Level 3 Expert

5938 Answers

Are you a Samsung Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides