Uniden Radio Communications - Recent Questions, Troubleshooting & Support

If you get clear audio when close to the receiver, it would appear to be a problem in either the antenna or the receiver. Try a different antenna or relocate the antenna. If you adjusted the VSWR low it doesn't mean the power is radiating correctly. Verticals should be on roof, with roof as ground plane. Mounting on mirrors is ok, but doesn't work as well. Also, if you have sheet metal near the antenna, it acts as a ground reflector and can distort or block the waveform. You might also try it with a different receiver, in case yours has a faulty pre-amp stage. It could also be a power amplifier problem in the transmitter, where it shows 5 watts but isn't putting out that amount. You can check it with an RF watt meter.

Uniden Radio... | Answered on Jul 01, 2019

Trying to wire a dm-452 4 pin mic to a 5 pin uniden ... - Fixya

Jan 6, 2014 - trying to wire a dm-452 4 pin mic to a 5 pin uniden washington -Uniden Bearcat Pro PC68XL ... SOURCE: trying wire a superstar dm-452.

How to wire a superstar DM-452 to a five pin uniden and ...

36 mins ago - how to wire a superstar DM-452 to a five pin uniden and washington - Uniden CB Radios question.

Wire superstar dm 452 mic - Answer

... to a 5 pin how to wire a dm-452 superstar 4 pin mic to a 5 pin uniden washingtonit's not possible to wire 4 wire mics to the uniden 5 wire radios without ...

Uniden Bearcat Pro PC68XL 40-Channels Base CB Radio ...

Uniden Radio... | Answered on Jun 29, 2019

Uniden Pc76xl Manual FREE Download - Ebookread..click on this if t don't work just copy and paste and put it into google.
hope this helps you out.let me no how you get on.
i was on the cb for over 30years myself so good good luck 10.4 and out.

Uniden Radio... | Answered on Jun 19, 2019

Hold these 3 buttons all at once while turning the unit on (will take 2 hands)

Uniden BCT15X... | Answered on Jun 11, 2019

Yes, it does sound like a bad power transformer. Try powering it using a DC supply or battery and see if the hum goes away.

Uniden BC60XLT-1... | Answered on Jun 09, 2019

How do we sconne frequency channel in a uniden scanner bct15

Uniden BCT15X... | Answered on Jun 06, 2019

If you have access to the Internet then Google that particular county government radio frequencies and try the one that it gives you . Hf,vhf,uhf??

Uniden Radio... | Answered on Jun 02, 2019


Download user manual and read instructions at page-9, your problem will be solve.

Uniden Radio... | Answered on May 22, 2019


it looks something went wrong with the program.

I will suggest to make a hard reset to the unit.

if its not helping - maybe you will need to reprogram the unit,



Uniden Radio... | Answered on May 07, 2019

Press scan then press key pad numbers to enable banks. All of your programmed frequencies may have been erased.

Uniden Radio... | Answered on Apr 25, 2019

An older uniden for a frequency range between 100 and 199 mhz may expect you to interpret the frequency being shown as 1 followed by other digits on your display. For example a frequency of 145.350 may expect you to mentally add the printed "1" and digits 45350 giving the total frequency. This saved the manufacturer from having to purchase another digit to display the frequency since it is always 1 to start with.

Uniden Radio... | Answered on Apr 08, 2019

Not finding what you are looking for?
Uniden Logo

3,428 questions posted

Ask a Question

Usually answered in minutes!

Top Uniden Radio Communications Experts


Level 2 Expert

218 Answers

Robert McClure

Level 2 Expert

161 Answers


Level 3 Expert

1655 Answers

Are you an Uniden Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides