Uniden Logo

Uniden Recent Questions, Troubleshooting Help & Support

Do you work here? Claim your company

  • 2K Products
  • 77K Answers
  • 2M Views

it means the disk is damaged otherwise you have a software problem and not a hardware problem
see:
https://inro.in/hola-vpn/
https://inro.in/private-internet-access/
https://inro.in/tunnelbear/

Uniden Lands... | Answered on Nov 05, 2018


I found the Uniden 2.4GHz XS1410 cordless phone manual on the product page from Uniden Australia: http://www.uniden.com.au/australia/p_xs1410_index.asp. The direct link to the manual is http://www.uniden.com.au/resources_main/pdfs/XS1410_OM.pdf .

I hope this helps.

Cindy Wells

Uniden Cordless... | Answered on Nov 05, 2018


Hello, Kenneth -

The user manual for the Uniden corded / cordless telephone model D3098 can be found here:
https://teltex.com/content/userguides/Uniden-D3098-User-Guide.pdf
(PDF document, Adobe Acrobat Reader software needed to download and save to a computer - software is free)
Instructions for the Answering System begin on Page 21.

If you need more assistance, the Customer Care phone number can be found on Page 1.

Best wishes.

Uniden Lands... | Answered on Nov 03, 2018


as they always have , hand set does not store messages like cell phones

Uniden Lands... | Answered on Nov 01, 2018


On your phone, make sure bluetooth is turned on (settings, general).

While your phone is in discovery mode, turn your bluetooth device on and put it in discovery mode (usually you have to hold the power button for 7-10 seconds).

Your phone will find the device, and you will be prompted to enter the devises PIN number (often 0-0-0-0). Your phone should pair with the device then.

Uniden BT-108... | Answered on Oct 27, 2018


try dialing in #43# into handset while dial tone heard

Uniden Lands... | Answered on Oct 26, 2018


I had a similar problem which I finally fixed. You did not say if any of your phones registered.
First try the following recommended by Uniden Support:
Your phone(s) should be fully charged before putting them on the main base.
Unplug the battery from the phone by removing the battery cover and removing the connector. Then, push the # and * key together and hold while you plug the battery back in (requires some dexterity). Continue to hold the two keys until you hear a confirmation tone. This will force the phone to reregister. Put the phone on the main base (if you are sure it has a fully charged battery) and see if it will reregister it to solve the problem.
That did not work for me. So, I followed the instructions to de-register the handset (even though it hadn't really registered). But, I also pretended like the Base was not available (because using the base in this step also failed).
1) Press and hold the hang up and # keys for at least 5 seconds.
2) Move the cursor to select Base Unavailable and then press Select.
3) Select the base you want to deregister from, press Select and then move the cursor to Yes and select.
This causes the phone to delete any of its base information.
At this point, again insure that your phone shows the battery is fully charged and if it is not, put it on the stand alone charger base (not the main base). With the battery fully charged, place it on the base and try registering again by placing it in the main base.
If neither of these approaches help, contact support at Uniden.com.
However, my problems were cleared when I cleared the handset with the second set of instructions.

Uniden DECT 6.0... | Answered on Oct 25, 2018


try their website NOT FIXYA

Uniden Lands... | Answered on Oct 23, 2018


Google (uniden)(model)(manual) without parens for instructions.

Uniden DECT 6.0... | Answered on Oct 22, 2018


I was getting the same trouble with the "record file error" always showing up on my monitor as well, and no recordings were being written into the SD card. I tried different SD cards and the same message was appearing. I was about to pack it up and return it to the store until I did one last thing...and it worked for me! Solution: Using a paper clip, insert the end of it into the "reset" hole under the SD slot and the system will turn off, restart, and voila!...it will start recording again. I hope this helps everyone who has this similar problem out there. I guess the unit just need a good reboot and get some of the bugs out of it's system.

Uniden Guardian... | Answered on Oct 20, 2018


Often I found a scanner needed all the positions to be filled.
My older Bearcat did. For instance 151.575. Perfectly fine, yet the scanner would not save it. If I put 151.57500 in, it takes it every time. Go figure! If that did not fix your question, please ask again.

Uniden Radio... | Answered on Oct 20, 2018


Google (uniden)(model)(manual) without parens for instructions..

Uniden Lands... | Answered on Oct 20, 2018

Not finding what you are looking for?

Ask a Question

Usually answered in minutes!

Top Uniden Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Ekse

Level 3 Expert

13434 Answers

The Knight
The Knight

Level 3 Expert

76140 Answers

Are you an Uniden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...