20 Most Recent 2006 Mitsubishi Colt Questions & Answers


First you have to check power steering fluid level, and if it's ok then you have to check power steering pump. If you have a EPS light on your dash, then you have to plug a ODBII diagnostic tool to read code and then interpret what the problem is.

2006 Mitsubishi... | Answered on Dec 22, 2019


Sounds like you have a fuel issue i recommend replacing the fuel filter it is the first and cheapest option. contact me for assistance with removal and installation for your vehicle.

2006 Mitsubishi... | Answered on Oct 10, 2019


There are no diagrams of that that I know of //// oil is pumped into the engine and travels through the engine block to lubricate the cam and timing chain/s OHV OVERHEAD VALVES nto the valve lifters then up through the push rods into the cylinder heads to lubricate and cool the valve springs and the cam/s if Daul overhead cam THERE'S 2 AND 2 CHAINS THAT'S HOW THEY WORK WHAT IS THE PROBLEM IF ANY THAT YOUR HAVING?

2006 Mitsubishi... | Answered on Sep 08, 2019


solved cheers!

2006 Mitsubishi... | Answered on Mar 14, 2019


My EPS on my mitsubishi colt 2006 stopped working about 8 months now, I changed the electronic box,but it started to work for ten minutes and then stopped.I carried it by some electricians and they put the computer on it, but it is not getting through.Could someone lend some assistance!!!!!!!!!!!!!!!!!!!!!!!!1

2006 Mitsubishi... | Answered on Jan 23, 2019


Its in the fuel pump.

If you need further help, reach me via phone at https://www.6ya.com/expert/kelley_9a924afdf232bd4d

2006 Mitsubishi... | Answered on Jan 14, 2018


indicates a wheel alignment problem
have the rear suspension checked and aligned first then have the front redone
the car could be going sideways down the road because the rear wheel are not in line with the front tires
not self centering and stiff indicates not enough castor

2006 Mitsubishi... | Answered on Nov 22, 2017


The ECU would have to match the part number EXACTLY. You're much better off getting your current ECU rebuilt and programmed by the rebuilder.

2006 Mitsubishi... | Answered on Aug 26, 2017


Central locking works by way of little electric motors that engages and disengages the door lock. The drivers door has an additional set of contacts in the actuator which signal the controller when it changes position. The controller activates the servo motors when a signal is received from the receiver or from the drivers door servo motor. So in your case I suspect the motor part of the drivers door actuator is done for.
To replace you will have to remove the inner driver's door panel to get at the actuator. The actuator itself cannot be repaired and needs to be replaced as a unit.

2006 Mitsubishi... | Answered on Nov 25, 2016


check the hanger and brackets for missing or broken/bent --also check the heat shield may be out of place --start up is when the engine shakes and vibrates the most --when idling it smooths out and the engine mounts take up the smaller vibrations

2006 Mitsubishi... | Answered on Aug 05, 2016


Have you looked in the owner's manual for the location? It must be in the underhood fuse and relay center.

2006 Mitsubishi... | Answered on Jun 10, 2016


look for a dome light switch on dash if the are really small lights and show up at night you have map lights 

2006 Mitsubishi... | Answered on Jun 05, 2016


Hi, your problem is your brake caliper it could be its not coming on properly to lock on to the disc . When they don't lock on like they should you will get a squealing also on some disc brakes you get anti squeal shims fitted. With some lower quality brake pads you may get squealing. I don't know what kind is fitted on your motor brake pads but its worth another look . The worst outlook is the brake pads are worn right down and you are grinding metal to metal ie disc to pad without anything in between.Should get it looked at.

2006 Mitsubishi... | Answered on Dec 23, 2015


The sensor is behind the bumper reinforcement panel.

2006 Mitsubishi... | Answered on Apr 28, 2015


If it engages in 4WD and works noramly in 2 and 4 wheel .
Then I would look to the switches . A lose wire bad connection or if a cable is involved a slight adjustment
Dosn't sound like you have a big problem .You will have to do a little research on how the system works being some are vacuum with cable some electronic even the same vehicle same year im not sure what Mitsubishi used in the colt in that year .
But mitsubishi are build very well good engieneering

2006 Mitsubishi... | Answered on Apr 11, 2015


If you mean turn signal flasher, look at fuse box.

2006 Mitsubishi... | Answered on Dec 17, 2014

Not finding what you are looking for?
2006 Mitsubishi Colt Logo

369 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Colt Mitsubishi

  • Colt Mitsubishi

Most Popular Question

oil flow diagram mitsubishi colt 2 8 tdi

  • Cars & Trucks
Loading...