1984 Chevrolet Celebrity - Answered Questions & Fixed issues


see if your low and high beam are not out

1984 Chevrolet... | Answered on Oct 05, 2013 | 55 views


sounds like a bulb is out check lights and signals if not change flasher box its only a cheep fix

1984 Chevrolet... | Answered on Oct 05, 2013 | 53 views


You have a front and rear with a T in line that splits both sets

1984 Chevrolet... | Answered on Sep 07, 2012 | 43 views


You seldom feel a misfire at cruise. You have a misfiring cylinder(s)

1984 Chevrolet... | Answered on Mar 17, 2012 | 238 views


First, drain your system's coolant into a container (and dispose of properly)
Locate the two hoses that go into your firewall. These hoses go into and out of the hearer core and remove them. There should also be rubber insulators on the inlet and outlet of the heater core. Unscrew each hose's fastener and remove these hoses. Do not dispose of these hoses as they will be reused. Next, go iside of your vehcle and remove the under dash cover and then locate the heater duct. It has a number of small screws plus clips that hold it in place, remove them. The duct should then be removed. There is also a small cover over the heater core inlet/outlet pipes. It is held on with three screws, one of which is a little hard to see, remove them and take off the small cover. It may be glued in place by a tar like insulating material. The heater core is held in place by two strap clamps over it which are held on with two screws in each. Finally, Remove the screws and clamps. The heater core will now come out
Reverse the procedure to install the new heater core. Refill the coolant and check for leaks.



Read more: http://wiki.answers.com/Q/How_do_you_replace_heater_core_87_celebrity#ixzz1DncDAfbn

1984 Chevrolet... | Answered on Feb 13, 2011 | 355 views


You will have to disconnect negative battery cable, then disconnect wiring harness going to gas tank, then remove filler tube, then both fuel lines.
Then support the tank with a jack, remove support straps, then remove tank bolts, lower tank and pull it out.
Then with a BRASS and ONLY a BRASS punch and a hammer, knock the ring on top of the tank counter-clockwise until it is completely loose. Then pull out sending unit and fuel pump carefully and disconnect the two of them. Then reverse procedure to reinstall new pump

1984 Chevrolet... | Answered on Apr 10, 2010 | 111 views


it could be the flashing signal switch, the electrical wires in the stearing colum sometime brake, try that. hope it helps you. in order to remove it you need to take cover of stearing colum and usually one plug and two bolts hold it in place. good luck

1984 Chevrolet... | Answered on Mar 18, 2010 | 225 views


Possible dirty MAF sensor. Try usin a can of MAF sensro spray from auto parts store on MAF sensor while sensor is out of vehicle and engine is not running

1984 Chevrolet... | Answered on Feb 22, 2010 | 94 views


84 celibrity has a carborater and the filter is in the carb. where the fuel line connects to it. Follow this metal line down past the timing cover and the other end screws into the fuel pump thats connected to the side of the engine block near the oil pann gasket on the belt drive end of the engine it has some brackets surounding it for the power steering pump and it's hard to get to and lots of other stuff needs to be removed to get to it. When their bad they leak oil too and sometimes they leak gas into the oil.195379185.jpg

1984 Chevrolet... | Answered on Nov 28, 2009 | 250 views


Probably not easy to do on a front wheel drive car, unless you are a small contortionist.

I would give this job to an auto repair shop.

1984 Chevrolet... | Answered on Oct 10, 2009 | 103 views


If your engine has a carburator it is in the carb. You will see a big nut where the fuel line goes into the carb. Unscrew it and there is your fuel filter. If you have TBI or throttle body, it's inline, under the car I think. Hope this helps.

1984 Chevrolet... | Answered on Dec 18, 2009 | 179 views


Ditch the A/C system...get that compressor out of there....that's a start!

1984 Chevrolet... | Answered on Jun 27, 2009 | 22 views


It's not as easy as it sounds. Basically you will need to lift the engine off the frame and unbolt the old ones off. I highly doubt that you can do this without disconnecting the transmission. Definitely something that you want an experienced mechanic to help with. It may just not be worth it. If you can lift the engine with the transmission attached (if there is enough room to tilt it up), that would be the best bet but you will need an engine hoist or cherry picker to do this. (THIS IS NOT FOR AN AMATEUR)

Let me know if you have any further questions, this will require a lot of work

1984 Chevrolet... | Answered on Mar 27, 2014 | 152 views


Is this a 2.8L vin W? I saw a service bulletin that said, do not replace maf sensor for maf sensor code. You install a new mem-cal. The new memcal doesn't use the maf signal, but does use the mat. If the update had been done on your vehicle, there should be a decal under the hood to notify you about the update. They did this because of problems with the maf sensor, at the time.
Just to add, problems at higher rpms, check for a blockage of some kind, air--fuel--exhaust. Use a gage and check proper fuel pressure.

Chevrolet... | Answered on Feb 15, 2018 | 43 views


Yes the pump could be the problem .blown head gaskets are also a possability

Chevrolet... | Answered on Sep 01, 2017 | 54 views


under the dash on the driver side u should see the fuse block were all the fuses are there will be a round silver looking thing ,it will be about as big as a quarter this will be your flasher relay

Chevrolet... | Answered on Jan 03, 2015 | 225 views


037f845.jpg

Fig. 31: Chevrolet 2.8L VIN X 2BC - 1985-86 Federal models (click for zoom)

bd6b99a.jpg

Fig. 32: Chevrolet 2.8L VIN X 2BC - 1985-86 Taxi Federal models

086d0bd.jpg

Fig. 33: Chevrolet 2.8L VIN X 2BC - 1985-86 Taxi Canada models

f593b1d.jpg

Fig. 34: Chevrolet 2.8L VIN X 2BC - 1985-86 Taxi California models

f6a7573.jpg

Fig. 35: Chevrolet 2.8L VIN W TBI - 1985-86 Canada models


Hope this help (remember rated this).

Chevrolet... | Answered on Sep 23, 2014 | 375 views


To reset the PCM to render a more performance program has to be done by an expert. There is nothing substantial you can accomplish with having the means to reflash the PCM. There are many places that do this but I need to know if this is a Celebrity or a Camaro.

Chevrolet... | Answered on Mar 24, 2014 | 90 views


looking for a n acuater(heater valve0

Chevrolet... | Answered on Nov 11, 2013 | 95 views


If it is V6 ive seen a lot of these have a bad crankshaft position sensor causing that
same issue.

Chevrolet... | Answered on Oct 31, 2013 | 123 views

Not finding what you are looking for?
Cars & Trucks Logo

30 questions posted

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...