Top 10 1991 Honda Accord Questions & Answers

1991 Honda Accord Logo

Question

  • 4,541 People Helped

I need a wiring diagram to install a kenwood

I need a wiring diagram to install a kenwood kdc-248u?

Posted by on

Answer

  • Most Helpful of 1 Answers

You can get the wire diagram on the link below page 18.

http://a248.e.akamai.net/pix.crutchfield.com/Manuals/113/113KDC248U.PDF

Posted on Apr 03, 2011

Question

  • 3,926 People Helped

1992 Honda Accord LX won't start - ignition problems

I have a 1992 Honda Accord LX that was running fine and then died abruptly.

I have tested the fuel pressure (40 psi constant and holds for quite some time).

I pulled the coil wire from the distributor cap and found that it had no spark (when holding next to metal) when the vehicle was trying to turn over. I replaced the spark plugs (there was some oil in two of the plug wells that concerned me), wires, cap, rotor and coil. I also replaced the valve cover gasket that was leaking the oil into the plug well.

Alas, it still will not run (it just turns over). I followed the instructions found at AutoZone.com and tested the pick up coil (located in the distributor) and found that it is ok (power where there should be power and resistance tests ok in accordance with their specs).

Any ideas?

Posted by on

Answer

  • Most Helpful of 5 Answers

you have to replace the main relay located inside the car, its located underneath the cruise control module, on the drivers side

Posted on Jun 15, 2009

Question

  • 3,538 People Helped

diagram of the 1991 honda accord firing order

diagram of the 1991 honda accord lx

Posted by on

Answer

  • Most Helpful of 2 Answers

  • Here is the diagram you requested. Cylinder 1 is on the right side.



11_1_2011_7_20_16_am.gif


Hope this helps.

Posted on Nov 01, 2011

Question

  • 3,503 People Helped

how to disable honda accord 1997 Immobilizer

how to disable honda accord 1997 Immobilizer.I misplace the master key of my honda and i have a spare key but would not pass the immobilizer.how can i recode the new key or disable the immobilizer before i find the master key..
Thank you

Posted by on

Answer

  • Most Helpful of 2 Answers

I show immobilizers where only started in the 1998 accords, if you have a remote starter and they used a key in the box bypass all you need to do is find the box under the dash open it up and use the key

Posted on Jan 31, 2010

Question

  • 2,967 People Helped

i need to know how to align timing belt and balancer shaft belt on 2.2 honda engine

diagrams would help

Posted by on

Answer

  • Most Helpful of 1 Answers

I had the same problem with my 92 Accord I found an arrey of helpful videos on this I typed in, (92 accord timing belt.)

Posted on May 17, 2012

Question

  • 2,952 People Helped

need to know how the timing marks are set on a 91

need to know how the timing marks are set on a 91 honda accord

Posted by on

Answer

  • Most Helpful of 2 Answers

I assume your talking about the timing belt marks for the crank and cam,heres a diagram to help you.6d7e9bc.gif86bd7b3.gifb7e773c.gif

Posted on Oct 01, 2010

Question

  • 2,939 People Helped

diagnostic trouble codes for a 91 honda accord

diagnostic trouble codes for a 91 honda accord

Posted by on

Answer

  • Most Helpful of 1 Answers

chuckster57_3.gif
The list is above

Posted on Dec 25, 2010

Question

  • 2,682 People Helped

How do you replace ignition cylinder in 1991 Honda

How do you replace ignition cylinder in 1991 Honda Accord?

Posted by on

Answer

  • Most Helpful of 3 Answers

It is recommended, if you have an automatic transmission, that you change the entire ignition switch assembly(the entire apparatus that goes around the steering column and is held in place by two shear bolts that have to be drilled out and require that you remove the steering wheel, the shields behind it and the instrument panel)
It is recommended that you remove the steering wheel HOWEVER, If you have an SRS (air bags) most manuals will tell you to have the work done by a Honda dealer, because disarming the SRS is a bit involved, and there’s no way for you to test it after you have done the job. If you don’t have air bags just remove the steering wheel and ignore the parts that come later here involving how to do things without removing it.
It is possible to change the ignition key lock on a Honda Accord Automatic, without removing the steering wheel and/or disarming the SRS, IF you are willing to take your time and exercise special effort. Since I have changed the lock myself, without removing the steering wheel, I know it can be done. Also, the entire switch costs a fortune, whereas the lock and keys can usually be had on eBay for around $30.00. If you want to give it a try, continue:
First, take both cables off the battery. Before you do, make sure that your radio isn't one of those anti-theft jobs that needs a code when you hook the battery back up. If you don't have the code, no more radio.
Next, remove the shields behind the steering wheel. There are seven screws in the bottom shield, four threaded and three pointed. Remember where they go. After you have removed them, ease the portion of the bottom shield out from around the key lock, then it will be loose. If you have a tilt-wheel model, you will have to push the lever down (while holding the steering wheel where you want it) and then the shield can be pivoted so that it will come off the lever. Then push the lever back up.
The top shield will pull out from the top position with only minimal easing upward and outward.
After the shields are removed, you will see that the lock is behind the wiper apparatus and that the set screw that holds it in (Philips head) can not be accessed in the normal manner (with the steering wheel removed). Don't give up yet. First, remove the illumination bulb from the plastic shield around the lock itself. Turn the bulb holder about ¼ turn and it should then come out of the housing. Then, remove the plastic shields themselves. There are three of them and they will all come off after you figure out how various plastic parts clip minimally onto the lock. It just takes a bit of working back and forth. When you have the shields off, you are ready to remove the lock itself.
At this point, insert the key into the lock and turn the lock to I. Leave it there.
Two maneuvers that would be very easy if the steering wheel were removed are more difficult this way, but they can be done with slow care and effort. First, the set screw has to be loosened, NOT removed. Using a good pair of needle-nose pliers, you can carefully turn the screw out until the lock will clear it (you can see the inner point of the screw where it blocks the locks removal, so you should be able to see when it no longer will cause such a block). Next, you must push in the pin that is part of the lock itself and comes up in a hole in the casing just a short distance back from the set-screw (you may need a flashlight to see the hole). Now, since you don't have the steering wheel removed, you can't simply push a small philip's head screwdriver into the hole to compress the pin. You will have to use something like an allen wrench (with the 45% angle) of the proper size to fit into the hole and carefully fit the end into the hole while holding the longer end. Even then, you probably won't be able to get enough pressure on the allen wrench to push in the pin unless you carefully insert a flat-bladed screwdriver behind the wrench and lever it into the hole. I know, sounds like you need three hands, but if you are careful, and give yourself plenty of time, it will work.
Once you have the pin compressed, with your fourth hand you can work the lock out of the casing. Okay, sometimes the pin will pop back up and you will have to compress it again, but if you work the lock out as much as possible (just a hair) before compressing the pin, it will tend to catch the pin under the casing so that you can continue with removal.
When you have the lock out, you will find that it still has one wire connected to it by what appears to be a piece of plastic with the screw through it. Remove the screw, then, CAREFULLY pry up the end that the screw goes through and remove the plastic part by moving it slightly in the direction of the screw hole and lifting it up (there is a tiny tab at the other end of the part that fits into the lock, so you will have to put that end in first when you connect the part to the new lock). Okay, get your new lock, making sure that it is the same as your old lock and attach the plastic part and screw in reverse of how you took them off.
Now, with the new lock with key inserted and turned to I, carefully slide it back in to the same position as the old one was when you removed it. It should, perhaps with only a slight amount of pressure, click into place (the pin comes up in the hole). When that is accomplished, you should try the key to see that it turns through it positions easily.
If it does, carefully (using the needle-nose pliers) tighten the set-screw that holds the lock in position. Then replace the three plastic lock shields and put the illumination bulb back in simply by reversing the turn by which you took it out.
At this point, you should hook your battery back up and see it everything works as it should before you go through the trouble of reinstalling the top and bottom shields. Start the car.
If it starts, give it a short test drive to make sure it runs and shifts properly then turn it off, replace the shields and congratulate yourself on having done that which they all said couldn't be done.
I hope that this helps you.

Posted on Oct 22, 2009

Question

  • 2,609 People Helped

Car idles erratically-surges and revs up and down

Motor surges and idles erratically until car warms up-when I put the car in neutral, it revs up and down. Sometimes the car tries to surge forward while in drive with my foot on brake-for example sitting at red light-usually only when car is still warming up. Also, the temperature guage on dash does not work. Engine light comes on after car warms up. Dont think the motor is getting hot and all fluid levels normal. Do you think this is a sensor or throttle body prob.

Posted by on

Answer

  • Most Helpful of 5 Answers

1.Verify that the cooling system is full of coolant and there is no air in it. 2. Remove the air boot from the throttle body and cover the throttle body with something that will stop the airflow . the Fast Idle Valve is the problem.

Posted on Feb 28, 2010

Question

  • 2,556 People Helped

check engine light code 15 on 91 honda accord dies while driving

we changed the coil thought it was fixed but started dying again. It seems as though it happens when car gets warm. now its happening more frequently. What repair will fix this? it almost seems like a vapor lock

Posted by on

Answer

  • Most Helpful of 1 Answers

Have come across this before and have only had to replace any parts a couple of times. What I have found to be the problem in about half the cases was that there was a poor connection in the connector at the right shock tower. Also in about 30 percent of the case I have found an open wire that was just old and as it got hotter would lose it's continuity. Below is a picture of one of the connectors at the distributor. When you are having problems check to see if you have battery voltage at the yellow wire by using your negative battery terminal as your ground when checking for voltage and the key needs to be in the "on" position when checking. If voltage is not correct find the open wire. Last but not least, in the other connector at the distributer (see the next picture) where you see the leter "A" or terminal "A" with the key on and using the battery as a ground you should have about 10 volts there. If not correct, replace the ignitor. It may be heating up but as I said this is not common but have seen it before. Remember to check when the problem is happening when checking. Hope this helps.....

4_3_2012_11_29_47_am.jpg4_3_2012_11_30_11_am.jpg

Posted on Apr 03, 2012

3,427 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1992 Honda Accord
1992 Honda Accord

2,940 Questions

1995 Honda Accord
1995 Honda Accord

1,606 Questions

1996 Honda Accord
1996 Honda Accord

1,608 Questions

1998 Honda Accord
1998 Honda Accord

1,531 Questions

1994 Honda Accord
1994 Honda Accord

1,434 Questions

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

1991 Honda Accord Accord

  • 1991 Honda Accord Accord

Most Popular Question

want shift out right hesitate

  • Cars & Trucks
Loading...