Top 10 1996 Honda Accord Questions & Answers

1996 Honda Accord Logo

Question

  • 38,985 People Helped

1996 Honda Accord Timing Belt Installation. I need help.

I need to know how to properly install my 1996 Honda Accord Non V-tec's timing belt system. It blew out while I was accelerating normally at around 40-45mph.

Posted by on

Answer

  • Most Helpful of 8 Answers

You didn't post the size of motor so please use the one that is for you:

2.2L (F22A1) ENGINES
Install the timing belt, around the pulleys, in the sequence shown


26f5cb1.gif

a9d5be6.gif

Posted on Jun 30, 2009

Question

  • 15,229 People Helped

STILL CANT LOCATE THE INTERIOR FUSE BOX HONDA ACCORD 1.8 1996 MOD

U GUYS HAVE BEEN GREAT, BUT I WILL ADMIT I HAVEN'T LOCATED THE INTERIOR FUSE BOX FOR THE RADIO TO PLAY, IT GOT BLOWN WHEN A METAL FELL INTO THE CIGARRETTE LIGHTER. IN THE HOOD THERE'S A FUSE BOX AND THE ONE FOR THE RADIO IS WRITTEN ''BACK UP FUSE FOR THE RADIO'' AND IT SEEMS TO BE OKAY. I SUPPOSE THERE IS SUPPOSE TO BE AN INTERIOR ONE AND I HAVE SEARCHED FOR IT EVERYWHERE UNDER THE DASH BOARD... MAYBE ITS JUST NOT THERE OR I WILL HAVE TO DO WITHOUT RADIO! ANYONE GOT THE DIAGRAMS OR MANUEL IN ENGLISH? PLEASE SEND TO SMARTEDOS@HOTMAIL.COM

Posted by on

Answer

  • Most Helpful of 1 Answers

The 96 Accord interior fuse box is under the dash, drivers side. Look for the small access panel with a thumb twist on it. Picture below:
99631fb.jpg Fuse location in box is #1 below:
309c947.jpg Good luck.
Regards

Posted on Jul 21, 2009

Question

  • 9,161 People Helped

96 honda accord speedometer not working

not working

Posted by on

Answer

  • Most Helpful of 6 Answers

you need a new speed sensor located on the gearbox with 2 size ten bolts holding it on and a 3 pin connection going into it! heres a pic http://www.hondacivicrepairs.com/views/honda-civic-speed-sensor.JPG

Posted on Aug 13, 2009

Question

  • 8,492 People Helped

How to replace heater core

How to replace heater core 93 honda del sol

Posted by on

Answer

  • Most Helpful of 2 Answers

Heater Core Honda Civic/CRX/del Sol 1984-1995 Repair Guide REMOVAL&INSTALLATION
See Figures 1, 2 and 3
REMOVAL & INSTALLATION

  1. Disconnect the negative battery cable and disable the SRS system (if equipped.)
WARNING All SRS wire harnesses are covered with a yellow insulation. Read the SRS precautions found in this section and install the short connectors as described.
  1. Properly drain the cooling system.
  2. Disconnect and plug the heater hoses at the firewall.
  3. Disconnect the heater valve control cable.
  4. Remove the heater unit attaching nut on the firewall.
  5. Remove the dashboard as follows:
    1. Remove the center panel.
    2. Disconnect the wire connectors at the fuse box.
    3. Disconnect the sunroof switch connector, if equipped.
    4. Disconnect the ground cable at the right of the steering column and the power mirror switch wire connector.
    5. Remove the side air vent knob and face plate.
    6. Remove the screws attaching the air vent control lever.
    7. Remove the center panel, radio and heater control head.
    8. Remove the gauge upper panel (4-door) or instrument panel (3-door).
    9. Disconnect the speedometer cable.
    10. Remove the center upper lid.
    11. Remove the side defroster garnishes on both ends of the dash.
    12. Lower the steering column.
    13. Remove the dashboard mounting bolts.
    14. Lift and remove the dashboard assembly.
  6. Remove the heater duct.
0900c15280061a21.jpgFig. 1: Removing the heater duct assembly
  1. Remove the steering column bracket and duct assembly.
  2. Remove the heater assembly mounting bolts.
  3. Remove the heater assembly and remove the heater core.
0900c15280061a22.jpgFig. 2: Removing the heater case assembly 0900c15280061a23.jpgFig. 3: Removing the heater core from the heater caseTo install:
  1. Install the heater core into the heater unit.
  2. Install the heater assembly and the attaching bolts.
  3. Install the heater duct and steering column bracket.
  4. Install the dashboard assembly. Tighten the mounting bolts until just snug.
  5. Raise and attach the steering column.
  6. Install the center upper panel.
  7. Connect the speedometer cable and install the instrument gauge assembly.
  8. Install the control head, radio and center panel.
  9. Install the side vent and face plate.
  10. Connect the ground cable at the right of the steering column and the power mirror switch wire connector.
  11. Connect the sunroof switch connector, if equipped.
  12. Connect wire connectors at fuse panel.
  13. Install the heater unit attaching nut on the firewall.
  14. Connect the heater valve control cable.
  15. Connect the heater hoses at the firewall.
  16. Connect the negative battery cable.
  17. Fill, bleed and leak check the cooling system.

Posted on Sep 01, 2008

Question

  • 6,833 People Helped

diagram of firing order for a 1996 honda accord

diagram of firing order for a 1996 honda accord

Posted by on

Answer

  • Most Helpful of 1 Answers

2.2 liter

jturcotte_414.gif


2.7 liter

jturcotte_415.gif

Posted on Dec 08, 2010

Question

  • 5,747 People Helped

1996 Honda Accord 2.7L/V6 oil leak near oil filter/oil switch

I just noticed an oil leak that only occurs while my car is running and causes an oil drip about once a second. I already changed the oil pressure switch to be sure that was not it. While looking at the oil filter housing there is a plug just above the filter between the filter and the engine block. Initially the leak appeared toe be coming from there so I removed cleaned and reinstalled the plug using High Heat thread sealer which did not fix the problem. Subsequently, it seems the leak is coming from near the plug but not actually from the plug. It is very hard to see when I can only use a floor jack right now. I have also installed a new filter with an early oil change and this did not help. Has anyone had a similar issue and or have any ideas? Thanks in advance for any ideas

Posted by on

Answer

  • Most Helpful of 3 Answers

my car was doing the exact same thing and i spent about 18 hrs total trying to figure out. if you remove the oil filter, you will notice that the "bracket" that the oil filter attaches to is removable. remove the ENTIRE oil filter assembly. there is a bolt almost behind the crank pulley, its tricky to get to but you can get to it with a 1/4 in drive, swivel, and extension, i do believe it was a 10-12 mm socket (MUST BE ^POINT SHORT WELL) the top left bolt on the assembly you will notice that you can not get out. that is fine, take the rest of the bolts out and let the assembly hang from that bolt, BUT the bolt must me loosend all of the way to achive play in it. take a small screw driver and "break" the seal on the assembly. you will notice 2 holes. around those two holes is a single gasket. even the smallest crack will aloow oil to drip. my car was using about a gallon of oil every ten miles, so you can imagine how much oil i when through, replace the gasket. You can not get the rubber gasket ANYWHERE except a honda dealer. replace. put it together and you all set.

BASIC STEPS: RAISE PASSENGER SIDE.
REMOVE TIRE
REMOVE OIL FILTER
REMOVER ASSEMBLY
REMOVE GASKET
AND REPEAT BACKWARDS FOR INSTALLATION

Posted on Oct 26, 2009

Question

  • 5,043 People Helped

i had code p0758 solenoid circuit B electrical

transmission shift gear , engine light is on ..d3 green light blinking

Posted by on

Answer

  • Most Helpful of 2 Answers

Here is the definition of the code. You may need to have a transmission shop take a look at it.

P0758 HONDA Description Shift solenoid valve B is turned ON or OFF by the Transmission Control Module (TCM) in response to signals sent from the park/neutral position (PNP) switch, vehicle speed and Engine Control Module (ECM) (throttle opening). Gears will then be shifted to the optimum position.
Read more: http://engine-codes.com/p0758_honda.html#ixzz23fW0omun

Posted on Aug 16, 2012

Question

  • 4,106 People Helped

1996 honda accord vtec 2.2 timing marks diagram

diagram of 1996 honda accord vtec 2.2 timing marks

Posted by on

Answer

  • Most Helpful of 1 Answers

tHANKS I WILL TRY AUTO ZONE

Posted on Dec 03, 2012

Question

  • 4,060 People Helped

i need 1996 honda accord speed sensor plug wiring diagram

speed sensor plug wiring diagram


i need 1996 honda accord 2dr 2,2 liter vtech

Posted by on

Answer

  • Most Helpful of 1 Answers

Diagram is courtesy of honda

[IMG]http://i34.tinypic.com/10wjogi.jpg[/IMG]

Posted on Dec 09, 2008

Question

  • 4,050 People Helped

Wiring Diagram for 1996 Honda Accord EX

Where can I find a wiring diagram online (hopefully free) for a 1996 Honda Accord EX. I need to fix my cigarette lighter to power a GPS unit I bought. Also is there anywhere to get an owner's manual or specifications manual for this model? Thank you.

Posted by on

Answer

  • Most Helpful of 3 Answers

hondahookup.com

Posted on Sep 11, 2009

2,329 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1992 Honda Accord
1992 Honda Accord

2,940 Questions

1991 Honda Accord
1991 Honda Accord

2,649 Questions

1995 Honda Accord
1995 Honda Accord

1,606 Questions

1998 Honda Accord
1998 Honda Accord

1,531 Questions

1994 Honda Accord
1994 Honda Accord

1,434 Questions

Top Honda Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

1996 Honda Accord Accord

  • 1996 Honda Accord Accord

Most Popular Question

starts drives little stalls

  • Cars & Trucks
Loading...