20 Most Recent 2005 Cadillac Deville Questions & Answers


There is no secret button. It sounds like the linkage between the tilt lever and the tilt mechanism inside the steering column has come loose, or the mechanism is jammed. If that's the case, it's a complicated job to repair it, and because of the air bag in the wheel housing, should only be done by a qualified shop.

2005 Cadillac... | Answered on May 05, 2019


As you move the tilt lever to release the lock pawl from the rack the wheel will move. Yours does not it seems so the rack inside this tilt housing has broken off and has bounded up making the tilt option inoperatble. The steering column will be needed to be torn apart and replace this broken housing with a new one

2005 Cadillac... | Answered on May 05, 2019


On this website you find fuse box diagram and description for Cadillac DeVille (2005). Maybe it helps you

https://www.carknowledge.info/cadillac-deville-2005-fuse-box-diagram

2005 Cadillac... | Answered on Apr 24, 2019


Check G-302 for lose connection.
G302
Under the right front seat, on the number 2 bar near the inflatable restraint sensing diagnostic module

Terminal L driver seat switch connector . Black wire is ground to G-302 .Test by loading the circuit

2005 Cadillac... | Answered on Oct 14, 2017


Are you asking if it needs to be relearned or how to do a relearn ?

2005 Cadillac... | Answered on Feb 25, 2017


Under the hood on the engine , remove plastic engine cover ! Look for Search from over 10 Million Auto Parts

2005 Cadillac... | Answered on Feb 19, 2017


could be HO2S sensors not operational
low fuel pressure
problem injectors

2005 Cadillac... | Answered on Jan 12, 2017


It's a 40 or 45. Sorry , I can't be more specific. But I know it's one of those.

2005 Cadillac... | Answered on Dec 04, 2016


LOCATION
The camshaft position sensor is located on the rear cylinder bank in front of the exhaust camshaft. The camshaft position sensor extends into the rear cylinder head and is sealed with an O-ring.


26349435-oucqd2i3pucu3s1utbyq1gmo-1-0.gif

2005 Cadillac... | Answered on Nov 10, 2016


You most likely have a blown head gasket if you've been driving it hot. You have a bad thermostat or water pump or radiator or a leak...

2005 Cadillac... | Answered on Oct 28, 2016


B0429
Temperature Control 3 Circuit Range IPM
The actuator is an electronic stepper motor. The HVAC control module (IPM) supplies power and ground to the actuator. The IPM controls the direction of the actuator by changing the polarity of the control circuits. When the actuator reaches its desired position, both circuits are fixed to the same value (9.5-12 volts). The IPM determines the door position by counting pulses (voltage fluctuations) caused by the brush to commutator action generated during normal motor operation. The IPM monitors a voltage drop across an internal resistance to detect the pulses. The IPM converts the pulses to counts with a range of 0-255 counts.
When a calibration or recalibration procedure is performed, the IPM calculates the door travel range. The IPM commands the actuator to each extreme position and counts the total number of pulses. The IPM compares the total number of pulses to calibrated limits. If the total pulse count is less than or equal to the maximum calibrated limit and greater than or equal to the minimum calibrated limit, then the calibration is considered successful.
• Air Flow control 3 circuit refers to the mode actuator
• Air Flow control 7 circuit refers to the recirculation actuator
• Temperature control 1 circuit refers to the left air temperature actuator
• Temperature control 2 circuit refers to the right air temperature actuator
• Temperature control 3 circuit refers to the auxiliary air temperature actuator
Diagnostic Aids
• Inspect the appropriate actuator door and actuator for the following conditions:
- A misaligned actuator--Refer to one of the following:
- Mode Actuator Replacement
- Air Temperature Actuator Assembly Replacement
- Air Temperature Actuator Replacement - Left Side
- Recirculation Actuator Replacement
- Broken or binding linkages or actuator door
- Obstruction that prevents the actuator door from operating within its full range of motion
- Missing seals to the actuator door
- Misaligned seals to the actuator door
• Refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems.
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With the scan tool, command the appropriate actuator in both directions.
Observe the appropriate Actual parameter.
Does the scan tool indicate that the value of the appropriate Actual parameter changes from the minimum specified value to the maximum specified value?
0 Counts
255 Counts

P1574
Stop Lamp Switch Circuit
PCM
DTC P1574 in Cruise Control

DTC P1574 Stop Lamp Switch Circuit
This diagnostic test functions on the assumption that sudden decrease in a non-drive wheel speed must be caused by a brake application. Non-drive wheel speed and stop lamp switch status are supplied to the powertrain control module (PCM) through serial data from the electronic brake control module (EBCM). If there is a 2.5 mph or greater decrease of non-drive wheel speed in 0.4 seconds and a transition of the torque converter clutch (TCC) or extended travel contacts of the TCC brake switch without a transition of the stop lamp brake switch, DTC P1574 is set.
DTC P1574 indicates the stop lamp switch signal to the EBCM or the EBCMs ability to send the stop lamp switch signal to the PCM has failed. Refer to ABS/TCS DTCs for diagnosis of the stoplamp switch signal and the EBCM.
Connect the scan tool.
Turn ON the ignition, with the engine OFF.
Retrieve the DTCs from the electronic brake control module (EBCM).
Are any DTCs that begin with a "C" also set?
Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

2005 Cadillac... | Answered on Oct 25, 2016


Bought a bad PCM? Wrong one? Just got a PCM, it was for a 3.4 engine. They told the manager it would work for a 3.8. I told the manager it won't. Had to hook it up and prove it to the manager. Security was the first issue, then the transmission would be the next. I didn't even make it pass the security. A 3.4 PCM will run the 3.8 engine, with other computers replaced. But will not run the transmission correctly. And this is our problem. I told the manager to inform the customer that they had the wrong PCM. I also told him to give the car back. Then told him I could fix it, but needed PCM,BCM, Ignition switch,key and chip, from one junk car.

2005 Cadillac... | Answered on May 28, 2016


I WOULD ASK THAT SOMEONE TO REINSTALL THAT DISTRIBUTOR PROPERLY. NO PUN INTENDED. THAT MARK IS PROBABLY ON THE UPPER REAR/TRANS HOUSING. BUT FIRST THINGS FIRST. MAKE SURE THE DIST IS PROPLY INST. GOOD LUCK

2005 Cadillac... | Answered on Feb 07, 2016


Well dude you need to know how it's suppose work ! There is more to it then just a fuses ! there is a electrical circuit , power (B+) an ground an a control , a switch , a module etc... what ever ! Your best bet is to take it to a ASE certified repair shop or dealer ! Because it sounds like you know nothing about automotive electronics or electrical systems .

2005 Cadillac... | Answered on Jan 09, 2016

Not finding what you are looking for?
2005 Cadillac Deville Logo

393 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

DeVille Cadillac

  • DeVille Cadillac

Most Popular Question

2005 cadillac deville codes pcmp1574

  • Cars & Trucks
Loading...