20 Most Recent 2003 Toyota 4Runner Questions & Answers


How to time toyota wish
With engine number 1ZZ1910457

2003 Toyota... | Answered on Jul 15, 2019


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

2003 Toyota... | Answered on Jul 10, 2019


Put the claws of the compressor on a lower spiral in the spring.

2003 Toyota... | Answered on Jan 18, 2018


IF the lights are on, there's a code stored in the computer. Get the codes read and then you'll know what's going on.

2003 Toyota... | Answered on Dec 27, 2017


try a repair shop that service Toyota's you don't need to go to the dealer for this...

2003 Toyota... | Answered on Oct 04, 2017


I have read your problem. You can easily get the solution of your problem at the given site.I was also facing the problem few days back and this site helps me by providing the manuals and you can easily get the solution of your problem their. Please do visit it once. http://toolsnyou.com/

2003 Toyota... | Answered on Jul 31, 2017


check tail , brake and courtesy fuses , in engine compartment fuse box , and driver side fuse box under dash

2003 Toyota... | Answered on Jul 04, 2017


If yours is a 2003, you might look at changing the power steering fluid. I have a 97 Accord that would start jerking the steering wheel back and forth after it had warmed up. Replaced axles and didn't work, but replaced the fluid and it hasn't happened since. Wouldn't be hard or expensive to try. Just be sure to use the right fluid.

2003 Toyota... | Answered on May 16, 2017


not sure what remote you're talking about try being more specific we're not mind readers here.

If you're talking about your key chain remote that works your locks, it's probably got a dead battery. get a screw driver and pop it apart, go to walmart and look for the numbers on that battery and match them to a new battery.

done.

2003 Toyota... | Answered on Apr 03, 2017


check vacuum hoses or wiring to actuator on the transfer case
check actuator for operation

2003 Toyota... | Answered on Dec 17, 2016

Not finding what you are looking for?
2003 Toyota 4Runner Logo

501 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

4Runner Toyota

  • 4Runner Toyota

Most Popular Question

2003 4 runner base loose tighten

  • Cars & Trucks
Loading...