Question about 2006 Dodge Stratus

1 Answer

2006 dodge stratus,4 cylinder has loose torque converter bolts. How do i access them to tighten them up ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Take starter off

Posted on Jan 01, 2012

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Darrell

  • 118 Answers

SOURCE: NEED TORQUE SPECS AND SEQUENCE FOR 02 DODGE 2.4 V6 STRATUS

  1. Tighten bolts in sequence shown in (Fig. 23), using the following steps and torque values:
    • Step 1: Bolts 1 - 8 to 48 Nm (35 ft. lbs.)
    • Step 2: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 3: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 4: Bolts 1 - 8 to +90° . Turn Do not use a torque wrench for this step.
    • Step 5: Bolts 9 - 11 to 28 Nm (250 in. lbs.)
  • I tried to send a pic of the head bolt numbers but it wont let me so e mail me dbern002@att.net have a good day DB

Posted on Feb 01, 2009

Richard Scordino

  • 6982 Answers

SOURCE: Front caliper securing bolts torque

I know that it's a jag, and I know you are trying to be perfect, but in over thirty years, I've never seen a tech put a torque wrench on a caliper bolt. If you really want to I'd use about 35-40 foot pounds. (I go by bolt diameter) You don't have to slam them down but you don't want them to back out either. A bit over 35 is reasonable and should not damage anything and will keep them secure!
I have no idea what nm conversion is..

Posted on Apr 09, 2009

Anonymous

  • 218 Answers

SOURCE: I need some torque specs for the connecting rod

20 FT LBS + A 1/4 TURN

Posted on May 04, 2009

janman

  • 369 Answers

SOURCE: cant find the right bolt torque sequenceor bolt

Cylinder head bolts for 2.4 doch in ft\lbs
Step 1 .....................................................................................25
Step 2......................................................................................50
Step 3.......................................................................................50
Step 4.....................................Tighten an additional 1/4 turn (90-degrees)


the order is shown in this image:http://yfrog.com/2ocylinderheadj

Posted on Jan 25, 2010

ZJLimited

ZJ Limited

  • 17970 Answers

SOURCE: I need torque specs for the head bolts on a 2004

For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Posted on Aug 02, 2010

Testimonial: "I appreciate your quick response. Thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can anyone.tell me the Torqe specs for a 2004 or cruiser


Head and Cam Bolt Torque specs? - PT Cruiser Forum

www.ptcruiserlinks.com > ... > Tech & Performance Forum

Nov 5, 2012 - 2 posts - ‎2 authors
I am putting everything back on after replacing the head gasket. I was wondering what the Torque Specs and Sequences are for both the Head ... Torque Specs
10 posts
Jul 28, 2012
Valve cover torque specs
5 posts
Jul 4, 2011
Timing Repair Project - Bolt Torque Specs
7 posts
Jun 16, 2011
torque specs?
9 posts
Mar 20, 2006
More results from www.ptcruiserlinks.com

Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts ...

? 5:07
https://www.youtube.com/watch?v=2wB2o27eWgo
Aug 20, 2015 - Uploaded by World Mechanics
Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts Install and Torque Specs 2.4 Engine. ... 2004 Chrysler PT CruiserCamshaft Install

Dodge Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head ...

? 6:08
https://www.youtube.com/watch?v=7rY7tDbye-8
Aug 16, 2015 - Uploaded by World Mechanics
... Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head gasket Install and torque specs We took this video to ... 2004 Chrysler PtCruiser head gasket

Jan 18, 2016 | Cars & Trucks

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

I need torque spec. For camshaft pulley bolt on 2004 dodge stratus


2004 dodge stratus 2.7 L v6 200i--2006 engine identification is EER has twin cam shafts and the bolts that hold the sprockets to the cam shaft are at 21 ft/lbs
there are 4 bolts for each cam (autodata publication page 375)
if this is not your engine then comment as to how many cam shafts it has as there are many different settings for different dodge engines

Oct 26, 2015 | Dodge Cars & Trucks

1 Answer

What is the torque for the main and rod bearings on a 2005 dodge stratus 2.7L automatic v6?


Main bearing cap bolts there is a outer cap bolt that are torqued to 20 ft lbs + 1/4 turn. Then there a inner cap bolt that are torqued to 15 ft lbs + 1/4 turn. Con rod bolts are torqued 20 ft lbs +1/4 turn

Jul 06, 2014 | 2006 Dodge Stratus

1 Answer

I need torque specs for the head bolts on a 2004 Dodge Stratus Coupe 2.4L SOHC


For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

Step: 1 - Torque to 25 ft/lbs
Steps: 2 - Torque to 50 ft/lbs
Steps: 3 - Torque to 50 ft/lbs
Steps: 4 - Turn 90 degreesRecheck final torque in sequence

Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

Hope helps (remember comment and rated this).

Aug 02, 2010 | 2004 Dodge Stratus

1 Answer

How do i get my tranny off the motor i almost got that berring off inside of it but it still wont come down and all bolts are off in a 2001 dodge stratus rt and i need to do it fast


remove the starter motor and then look through the hole and rotate the engine and their are 4 bolts that hold the torque converter to the drive plate ,unbolt then 4 bolts and the torque converter comes away with gearbox ,also refit this way because you can damage the seal between primary input shaft and the torque converter also the first pump drive ring,it has two slots around primary shaft that locate into the back of the torque converter.best of british with it

Mar 30, 2010 | 2001 Dodge Stratus

1 Answer

Cant find the right bolt torque sequenceor bolt


Cylinder head bolts for 2.4 doch in ft\lbs
Step 1 .....................................................................................25
Step 2......................................................................................50
Step 3.......................................................................................50
Step 4.....................................Tighten an additional 1/4 turn (90-degrees)


the order is shown in this image:http://yfrog.com/2ocylinderheadj

Jan 21, 2010 | 1996 Dodge Stratus

1 Answer

2003 oil pan removal


4.0L Engine To Remove:
  1. Disconnect negative battery cable.
  2. Lift the vehicle.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    • Exhaust pipe from exhaust manifold.
    • Exhaust hanger at the catalytic converter and lower the pipe.
    • Starter motor.
    • Flywheel/torque converter housing access cover.
    • Oil level sensor (if equipped).
  5. Place a pole jack under vibration dampener with a piece of wood between dampener and jack.
  6. Remove or disconnect the following:
    • Engine mount through bolts and raise engine for clearance to remove pan.
    • Transmission cooler lines (if equipped).
    • Oxygen sensor harness from oil pan mounting studs.
    • Oil pan bolts and studs.
    • Oil pan and gasket.
To Install:
  1. Clean the gasket mating surfaces.
  2. Apply Mopar® Silicone Adhesive Sealant or equivalent onto the cylinder block in four location as shown.
7605306.gif

  1. Attach the pan gasket to the oil pan with Hi-tack or equivalent (2003-2005 vheicles).
  2. Use 1 ½ x ¼ inch bolts to fabricate alignment dowels. Cut off the head of the bolts and cut a slot into the top of the dowels (2006 vehicles).
4e495fd.gif

  1. Install two dowels into the timing case cover (2006 vehicles).
  2. Install two dowels into the cylinder block (2006 vehicles).
  3. Place the gasket over the dowels and onto the cylinder block and timing case cover (2006 vehicles).
  4. Position the oil pan.
  5. Install the 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm).
  6. Install the 5/16 inch oil pan bolts. Tighten to 132 in-lb (15 Nm).
  7. Remove the dowels.
  8. Install the remaining 1/4 inch oil pan bolts. Tighten to 84 in-lb (9.5 Nm) (2006 vehicles).
  9. Lower the engine onto the engine mounts.
  10. Install the through bolts and tighten the nuts.
  11. Remove jack stand and remove the piece of wood.
  12. Install the flywheel and torque converter access cover.
  13. Install starter motor.
  14. Connect the exhaust pipe to the hanger and to exhaust manifold.
  15. Install the transmission oil cooling lines (if equipped).
  16. Install the oxygen sensor wiring supports to the oil pan mounting studs.
  17. Install the drain plug into the oil pan. Tighten to 25 ft-lb (34 Nm).
  18. Lower the vehicle.
  19. Connect negative battery cable.
  20. Fill the oil pan with oil. WARNING
    Use extreme caution when the engine is operating. Do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.
  21. Start the engine and inspect for leaks.

Jun 06, 2009 | 2003 Jeep Wrangler

2 Answers

NEED TORQUE SPECS AND SEQUENCE FOR 02 DODGE 2.4 V6 STRATUS


  1. Tighten bolts in sequence shown in (Fig. 23), using the following steps and torque values:
    • Step 1: Bolts 1 - 8 to 48 Nm (35 ft. lbs.)
    • Step 2: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 3: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 4: Bolts 1 - 8 to +90° . Turn Do not use a torque wrench for this step.
    • Step 5: Bolts 9 - 11 to 28 Nm (250 in. lbs.)
  • I tried to send a pic of the head bolt numbers but it wont let me so e mail me dbern002@att.net have a good day DB

Feb 01, 2009 | 1997 Dodge Avenger

Not finding what you are looking for?
2006 Dodge Stratus Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...