Question about 1991 Buick Park Avenue
91 Buick PA won't start replaced crank sensor and coild pack. Think it's burning up crank sensor. Still not spark to plugs. Engine does turn over, but not full enough to start.
I just came across this problem myself the other day. i have a 91 buick park avenue that sometimes won't start. i checked several things out like cable connections and coil pack etc. etc. come to find out it was the wiring that came off the coil pack and connects to the crank sensor. the wiring that ran over top of the water pump had finally heated up so bad the coating on the wires had melted and when the engine got hot enough the wires would come in contact and send false signals to the computer not letting it start. after the car cools down and the wires contract it would start. so check the wires from the coil pack to the crank sensor to make sure the wires are not melted together.
Posted on Jan 16, 2010
This is for phantommech ... The first question I need to ask is whethe the key has a "pellet" on it which most call a chip. what you need to do is test the resistance on the key itself. If that key does not send a signal to the VATS system the car will think it is being towed and it will tell the ECM to not allow the starter to turn or the fuel pump to send gas to the carbeurator. If the key is fine... the next step you do is check to see if you are getting resistance... to do this there is an orange or black wire that houses two small white wires. Those wires run down the steering coulmn and plug into the ignition switch module. What I ended up doing was locating the VATS module itself and clipping the two wires that come out of the "BACK" of where those two wires were connected on the ignition switch. The VATS system is located behind the glove box. Run radio wire from the VATS module to the two coming from the steering column and connect them together. If you had to buy a new key lock cylinder then make sure you take the old key to a chevrolet dealer to find out what the VATS number is then have them cut the key with that VATS blank... The regular ILCO keys do not work at all I tried them and had to replace the key four times before having the dealer cut a new key.
Posted on May 04, 2009
Did you check to see if the mjagnet is still on the camshaft gear? Could possible be the ECM. Tap lightlyon ecm while cranking. Do you hear the fuel pump run for 2-3seconds after you turn the key on? Also if you replaced the ignition key from other than a dealer you may have the wrong resistance, plus there are 2 leads from the ign lock cyclinder that may be broken
Posted on Nov 29, 2008
Check ecm if it has a #1228253 replace it. GM had a cutting off problem with them. Clean battery cables too.
Posted on Apr 26, 2009
Could be the coolent sensor but most likely the ignition control modular or camshaft (not crankshaft) sensors. One by the pully the other by the water pump. I'd start with that one since you dont need a pully to get to it. Auto zone and napa test the ignition mods and say they are good, but the test they run on them does not get them hot enough they also check the coil pack. You might want to check the the wire leading to both of the cam shaft sensors as well.
Posted on Apr 23, 2009
I have a 97 Riviera that has a starting problem once in a while. Turn the key and nothing at all happens, excpet the lights all come on - but no starter.... no click even. I have always suspected the ignition switch, but your comments about the resistance chip in the key makes me wonder if that's it??
Posted on Jun 07, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Tips for a great answer:
Oct 10, 2014 | 1996 Buick Park Avenue
Jul 01, 2011 | 1994 Buick Park Avenue
May 14, 2011 | 1991 Buick Park Avenue
Jun 06, 2009 | 1991 Buick Park Avenue
Jun 06, 2009 | 1991 Buick Park Avenue
Aug 16, 2008 | Buick Park Avenue Cars & Trucks
5,304 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: