Tail light ground (possibly)

Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Go to http://www.bbbind.com/free_tsb.html free wiring diagrams ! You having tail light problems ? Do you know how they work ?

They are turned on by the BCM !
Park, Tail, Marker and License Lamps
The park, tail, license, and marker lamps are turned ON when the headlamp switch is placed in either the HEAD or PARK lamp positions, or anytime the automatic light control (ALC) turns the headlamps ON. When the headlamp switch is placed in the park lamp or headlamp positions, ground from G202 is applied through the signal circuit to the BCM indicating the park lamp request. In response to this signal, the BCM applies ground through the park lamp relay control circuit energizing the PARK LP PCB Relay. With the relay energized, battery voltage is applied through the switch side of the relay, both park lamp fuses, and the supply voltage circuits illuminating the park, tail marker, and license lamps. Ground for the left front park and marker lamps is provided at G101 and the right front park and marker lamps at G100. Ground for all rear lamps is provided at G302.
Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
?€¢
G101 provides ground for the left front turn signal lamp

?€¢
G100 provides ground for the right front turn signal lamp

?€¢
G302 provides ground for the left and right rear turn signal lamps

Wild guess, in the process of fixing the tail light, you disturbed the signal connections. Go back through your work carefully, see if something is loose or bad connection.

have u replaced the bulb? i believe some tail lights (all?) have 2 fillaments in bulb for tail light (running light) and using both for brake... blinker/ signal is a different bulb usually- that way u have running lights/ break lights at same time ur blinking.

The ground wiring on newer vehicles is a little complicated. Older cars, the ground would have been to the body around the tail-lights, but these have a ground wire in the harness and is connected to the turn-signal switch, and other sources. I don't think you have a ground problem. Does the fuse blow as soon as you press it into the fuse-block, or when you step on the brake? I believe you have a dead short somewhere, possibly a pinched turn-signal wire close to the tail-light assembly. Brake lights work through the turn-signal wires from the turn-signal switch on the steering column. That's how you can have one side blinking for turn while the other side stays on for brake. I'm kind of shooting in the dark here because I don't know what all you've done. If you replaced the turn-signal switch in the steering column, you may have pinched a wire or something there. Another thing, if the fuse doesn't blow as soon as you press it in, will both turn-signals work as long as you don't press on the brake? If you can provide a little more information, I might be able to help you more. One last thing....Have you replaced tail-light/turn-signal bulbs? If so, be sure you used the right bulb. You should only have two bulbs, one for back-up lights and one 1157-type combination for tail-lights and turn-signals. I have seen people use a single contact (1056) bulb in place of a 1157, which creates a short from brake/turn-signal back into the tail-light circuit. I do have a 1994 Dodge Dakota.

The turn signals and brake lights use the same circuit and filament in the bulbs. The tail lights are on the other circuit which comes from the headlight switch.
Do you have power on the tail light fuse ?

Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

If the brake and turn signal are on the same bulb than you can Orin straight wiring. If the brake and turn signal are on different bulbs than you'll need a wiring harness with a converter box. I'm pretty sure the wrangler has the brake and turn signal on the Same bulb so let's start with basic trailer wiring. The green wire on the trailer harness is for the right side turn and brake for the trailer. This wire should be attached to the wire on the vehicle that supplies power to the right turn signal/ brake light. The yellow wire is the left turn signal, brake light on the trailer and should be attached to the wire on the vehicle that supplies power to the left turn signal /brake light. The brown wire is the tail lights on the trailer and should be attached to either the left or right side wire on the vehicle that supplies power to the tail lights. The white wire is grounD and it is vitally important that this wire be attached to the vehicle in a manor that supplies a good ground. Failure to suppy a good ground will result in all kinds of funky problems with the trailerer lighting such as all the lights linking when the tail lights and turn signals are on at the same time. If you have any specific questions I will be more than happy to try and help. Good luck.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

any increase in bink speed is direcly related to a bulb being burt out.

Hi, you have a bad bulb,....