Question about 2006 Buick LaCrosse

1 Answer

How to remove front seat from 2006 Buick LaCrosse

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Buick Master
  • 15,575 Answers

Front Seat Replacement - Bucket
Removal Procedure
Caution: Refer to
SIR Caution in the Preface section.
Important: The front seat is equipped with a seat belt pretensioner. Disable the pretensioner before you perform any work on the seat.

  1. Disable the SIR system. Refer to SIR Disabling and Enabling and to SIR Disabling and Enabling .
  2. Remove the front seat head restraint. Refer to Front Seat Head Restraint Replacement .
  3. Position the front seat to the full forward and the full-up position.
  4. Remove the bolts from the rear of the seat adjuster.

Posted on Jun 21, 2016

Ad

5 Suggested Answers

Molson02536

Harvey N Tawatao

  • 3854 Answers

SOURCE: programing instructions for buick 2006 lacrossekeyless remote fob

Transmitter ProgrammingImportant: All transmitters which are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.

  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool. Important: The scan tool must stay connected until all of the transmitters are programmed.
  4. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  5. Repeat the previous step in order to program up to 4 transmitters.
  6. Remove the scan tool.
  7. Operate the transmitter functions in order to verify correct system operation.
Good luck

Posted on Dec 13, 2009

Ad

Anonymous

  • 416 Answers

SOURCE: how do I remove the back seat of a 2006 Buick

press it in at the bottom and lift up

Posted on Feb 17, 2010

Anonymous

  • 3 Answers

SOURCE: 2006 buick lacrosse how to replace headlight low

The bright light fitting is the same as the dim so take it apart fist to see how the cover screws off/on and the light comes out. Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. If not, then you need to release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. To remove these locking pins, pull or pry up the little tab in the center of the pin just like you were pulling a nail by the head. That should give you a little more space.

Posted on Apr 03, 2010

Anonymous

  • 3 Answers

SOURCE: change headlight 2006 Buick LaCrosse

The bright light fitting is the same as the dim so take it apart fist to see how the cover screws off/on and the light comes out. Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. If not, then you need to release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. To remove these locking pins, pull or pry up the little tab in the center of the pin just like you were pulling a nail by the head. That should give you more space.

Posted on Apr 03, 2010

dtadams115

  • 2 Answers

SOURCE: HOW DO I CHANGE THE

Asuming you mean taillight/turnsignal, and not highmounted brake light:
1.open the trunk
2.Remove 4 wingnuts on trunk trim (there are two on each side)
You can do it by only removing 2 on one side, but it makes a nicer job,
3.Pull back the trunk "trim" the carpeted cardboard
4.Remove 2 wingnuts which hold the taillight assembly in place
Pull out the taillight assembly; you might want to remove (i.e. unattach or unplug) the wiring harness
5.Turn the particular bulb's socket (there's 5 back there: 2 tail, 1 back up, 1 side marker, 1 brake/turn) counterclockwise, and it removes from the assembly, holding the bulb.
6. Pull out bulb and replace.
6. Reverse steps to reassemble.

Posted on Jan 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove a front passenger seat from a 2011 Buick LaCrosse


Usually two bolts on the back side to remove. Then pull it back and up. Unplug any wires going to it.

Jul 26, 2015 | Buick Cars & Trucks

2 Answers

HOW TO REMOVE THE FRONT SEAT


Do you have a bench seat or bucket seats. The difference between the two are: the bench seat is one seat, Bucket seats are individualy adjustible.

Jun 18, 2014 | 2007 Buick LaCrosse CXL Sedan

1 Answer

Oil sending unit location 2006 buick lacrosse


On or around the oil filter housing, may have to remove the oil filter on some models.

Mar 18, 2013 | Cars & Trucks

1 Answer

Where is the Radio Amp located in the 2006 Buick Lacrosse CX


likley in your trunk. There might be a removable panel held in place by screws, latches, or velcro

Jan 01, 2013 | 2006 Buick LaCrosse

1 Answer

2006 buick lacrosse - speedometer stopped working properly


Sounds like you need to replace your speedometer cable that runs from your dash to your transmission.

Dec 15, 2012 | 2006 Buick LaCrosse

1 Answer

My 2006 Buick Lacrosse warning light started dinging while I was driving and the seat belt light for passenger seat started flashing even though there was no one in the seat. After stopping the car I...


It sound like two or three separate problems, but it's hard to tell. The seat belt warning could be a faulty switch which senses a passenger in the seat, while the trunk lid opening could be a battery problem in the key fob. However, if the door locks still work with the same key fob, the problem is more likely with the lock on the trunk. Not starting after stopping could be a battery problem.

Sep 13, 2017 | 2006 Buick LaCrosse

1 Answer

After replacing the drivers side headlight assembly on a 2006 buick Lacrosse, the high beam hits the road very low. Is there an adjustment I've missed?


If they are adjustable, the adjuster screw would be visible just above or below the lens. Are you sure the bulb is seated in the socket? and seated into the light assembly squarely?

Aug 30, 2011 | 2006 Buick LaCrosse

1 Answer

Replace headlight on 2006 buick lacrosse


how do you remove r/h headlight assembly 2006 lacrosse to install low beam bulb?

Nov 15, 2009 | 2006 Buick LaCrosse

Not finding what you are looking for?
2006 Buick LaCrosse Logo

Related Topics:

1,803 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...