Question about 2005 Ford Explorer Sport Trac
Need firing order for 2005 ford explorer sport trac 4.0L 6 cylinder
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.
The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.
Posted on Apr 02, 2009
The engine is a 200 CID straight six, the firing order is 153624...
Just pop the distributor cap and have someone crank the engine while you watch the rotor.
How I can determine which hole in the distributor is assigned to the #1 plug wire.
Pull the number one plug. Turn the engine over slowly (with a wrench) while holding your finger over the plug hole. When the air builds (a lot of) pressure you are coming up to the number one spot on the distributor. (the rotor will point to the location of the #1 hole in the distributor.)
Quick methods to disable the engine I have seen people do on the classics:
Close the points by loosening the set screw
Pull the rotor cap
Connect a wire from the coil to ground. (effectively closes the points. Can damage the coil if key is left on.)
Pull the main ignition wire
And there are some tricks at the starter solonoid involving the ballast resistor bypass that is used to provide a hotter spark while cranking. (Two little wires at the starter solonoid - one is crank the other is the ballast bypass.)
Might give those a look-see. Best of luck (rememeber rated this help).
Posted on May 17, 2010
Testimonial: "This has been very helpful!! Thank you!"
Check in your Owners Manual or download this document from this link: Ford/maintenance/owners_manuals
Hope helps (remember to rate this answer).
Posted on Apr 11, 2011
Testimonial: "yes thank you, i went to the web site ford gave me and didnt help at all. this was very useful since i didnt get a manual with my truck. "
Tips for a great answer:
Mar 09, 2018 | Ford Cars & Trucks
Jan 10, 2016 | 2001 Ford Explorer Sport
Jul 05, 2013 | 2005 Ford Explorer Sport Trac
Jul 24, 2012 | 2005 Ford Explorer Sport Trac
Aug 22, 2011 | 2005 Ford Explorer Sport Trac
Mar 22, 2009 | 1998 Ford Explorer
Jan 18, 2009 | 2005 Ford Explorer Sport Trac
168 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: