Question about 2000 GMC Savana

1 Answer

Where is the cam sensor on a 2001 gmc 3500 serria 8.1

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • GMC Master
  • 85,216 Answers

  1. Raise and suitably support the vehicle.
  2. If the vehicle is equipped with the underbody shield package, remove the steering linkage shield.
  3. Disconnect the camshaft position (CMP) sensor electrical connector (3).
  4. Remove the CMP sensor bolt (2).
  5. Remove the CMP sensor (1).
  6. Inspect the CMP sensor for wear, cracks or leakage if the sensor is not being replaced.


where is the cam sensor on a 2001 gmc 3500 serria  - 9_27_2012_8_44_22_pm.gif
    Installation ProcedureImportant: Inspect the CMP sensor O-ring for wear or damage. If a problem is found, replace the O-ring. Lubricate the new O-ring with engine oil before installing.
  1. Install the CMP sensor (1).
    Important: The CMP sensor bolt has self-tapping threads, care must be taken, NOT to strip the threads when installing.
  2. Install the CMP sensor bolt (2). Tighten
    Tighten the bolt to 12N•m(106 lb in).
  3. Connect the CMP sensor electrical connector (3).
  4. Install the steering linkage shield, if equipped.
  5. Lower the vehicle.
  6. Posted on Sep 27, 2012

    Ad

    6 Suggested Answers

    6ya6ya

    6ya staff

    • 2 Answers

    SOURCE:

    Hi there,
    Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

    Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

    Here's a link to this great service

    Good luck!

    Posted on Jan 02, 2017

    Ad

    mikehumble

    • 124 Answers

    SOURCE: where is the cam shaft

    If this is a 5.7L the cam sensor is in the distributer and the crank sensor is in the timing cover

    Posted on Dec 16, 2008

    Anonymous

    • 5 Answers

    SOURCE: changing fuel pump on a 1989 gmc serria p/u

    buy an aftermarket electric pump from Summit Racing and mount it on the frame rail right near the filter....do not waste time dropping gastanks and paying for ridiculous gm type in the tank pumps, the in the tank pump is a giant fock u to the public from the automakers.....remember the little mechanical cam driven two bolt cuteys? 15 bucks and 15 minutes and you were done.... thanks big three!

    Posted on Feb 26, 2009

    JShreader

    JShreader

    • 50 Answers

    SOURCE: oxygen sensor

    Hello gobabygo1, my name is JShreader. Thank you for choosing fixya.com.

    There is 4 Oxygen Sensors on this model Truck. I uploaded a picture showing you exactly where each of the 4 Oxygen Sensors are located. It is in .pdf format. You can download it by clicking HERE. I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!

    Posted on Apr 01, 2009

    iambanshee74

    Kori Policy

    • 3489 Answers

    SOURCE: I have a 1999 gmc

    This sounds strongly like a PMD issue which is on the side of the fuel injection pump. Common issue and easily remedied. There are kits in which put the PMD in a different location as to avoid heat saturation. Let me know if you need to find one.

    Posted on Oct 26, 2010

    Konkomados

    • 157 Answers

    SOURCE: Were is the crank shaft sensor and the cam sensor

    Hello there,

    You can check in the side of the block, above the starter for the crankshaft sensor. As for the camshaft sensor, for a 8.1L engine, it is located on the front of the enigne, that is, at the driver side. You would notice it is a grey 3 wire connector. But for a 5.3/6.0L enigne, it is on top of the engine in the back.

    Best of luck!

    Posted on Jan 13, 2011

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Where's the knock sensors on a 2007 gmc serria 1500 5.3L


    under the intake plentium right in the middle of the valley between the heads. bad for wires getting corroded and rusted. it holds water in the knock sensor holes, you can buy the harness

    Mar 07, 2013 | 2007 GMC Sierra 1500

    1 Answer

    2004 3500 serria slow going in reverse


    if this is an automatic trans, check fluid level, it takes more fluid in reverse

    Mar 06, 2013 | 2004 GMC Sierra

    1 Answer

    How to change cam sensor 2001 gmc yukon


    how to change cam sensor gmc yukon model 2001

    Jul 18, 2012 | 2001 GMC Yukon XL

    1 Answer

    I need answer for truck not firing. On. A 1991. SERRIA 1500 TRUCK 5.0 LITER


    Several things can cause this problem, cracked distributor cap, old ignition rotor. Or if you have coil packs, cracked coil pack, ignition control module, crank position sensor, cam position sensor. Coil pack parts and sensors can be checked by autozone, cap and rotor will have corrosion on the rotor, however a small crack in the distributor cap can be next to impossible to see, replacement is usually best option.

    Feb 16, 2012 | 2000 GMC New Sierra 1500

    1 Answer

    Were is the crank shaft sensor and the cam sensor on a 2001 gmc 3500 truck? And I'm getting code p0700 p0335 p0342 p0155 on my 0bd2


    Hello there,

    You can check in the side of the block, above the starter for the crankshaft sensor. As for the camshaft sensor, for a 8.1L engine, it is located on the front of the enigne, that is, at the driver side. You would notice it is a grey 3 wire connector. But for a 5.3/6.0L enigne, it is on top of the engine in the back.

    Best of luck!

    Jan 13, 2011 | GMC C3500 Cars & Trucks

    1 Answer

    2001 dodge 3500 van cam position sensor location


    Crank sensor is in the bell housing of the transmission. Cam sensor is in the distributor.

    Jul 25, 2010 | 2001 Dodge Ram 3500 Truck

    3 Answers

    Changing fuel pump on a 1989 gmc serria p/u


    buy an aftermarket electric pump from Summit Racing and mount it on the frame rail right near the filter....do not waste time dropping gastanks and paying for ridiculous gm type in the tank pumps, the in the tank pump is a giant fock u to the public from the automakers.....remember the little mechanical cam driven two bolt cuteys? 15 bucks and 15 minutes and you were done.... thanks big three!

    Feb 08, 2009 | 1989 GMC Suburban

    Not finding what you are looking for?
    2000 GMC Savana Logo

    481 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    Marvin
    Marvin

    Level 3 Expert

    85216 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22485 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...