Question about 2002 Honda Odyssey

1 Answer

Tcs 2002 honda odyssey

TCS and CEL light on. Code on CEL is P0113/ high voltage read/low temp on IAT sensor (Intake air temperature). I replaced sensor, lights still come on and my TCS button stays off - I can push it in but the magnet does not cacth/button does not switch. Button has a ligh bulb fuse thing with a break in 1 of its 2 filament wires.

Posted by on

  • Kevin Pearcey Dec 11, 2012

    The Transmission was rebuilt 6 months ago but i recently replaced all my spark plugs so I bet that is it. I guess one may not be screwed in tight? I bought them new with proper metal: could one be bad out of the box. Every cylinder should have same spark plugs, right?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

  • Contributor
  • 41 Answers

I'd say a break in the wiring somewhere

Posted on Nov 20, 2017

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Sam Challis

  • 177 Answers

SOURCE: Honda Odyssey with 101,800. Maintained

With regard to the Transmission, some Honda's have strict procedures to follow with their trany's.
I hope you never had it flushed by a Quick lube or something like that. Also the type of fluid is very special in some of them too so mixing them with regular ATF will cause problems. I worked for a Forein Car Specialist and know how important it is to use only the Honda recommended fluids in them. If the light went out you can reset the code and see if it returns, if it does you may want a reputable shop to professionaly flush your tranny and replace the oil with Honda recommended oil.
With regards to your Catalytic converter, unless you can hear it comming apart inside (bang on it and listen if it rattles) or if the car is running extremly rich (gas will ruin the cat) you may have a blocked or ruined muffler farther down the system which is slowing the flow through the cat.
I hope this helps.
Regards
Sam

Posted on May 12, 2009

Anonymous

  • 38 Answers

SOURCE: 2000 Honda Odyssey - TCS Light stays on.

most likely some of your traction sensors are faulty

Posted on Jul 16, 2009

Anonymous

  • 1 Answer

SOURCE: tcs light and engine check light on my 2000 honda odyssey

I had the same code/symptoms a few weeks ago. Dealer did a nice job checking through all the details. Replaced the egr too, but no improvement. Finally found one cylinder not firing correctly (not the same pressure as the other cylinders.) Dealer did a value clean/adjustment, for about $250, and the problem has been gone for about a month now. We are also getting about 15% better mileage.

Hope this helps.

Posted on Sep 09, 2009

fixcar001

  • 202 Answers

SOURCE: My 2001 Honda Odyssey D4 light is flashing, CEL

the code 0715 is Mainshaft speed sensor, check the sensor see any loose connection or replace the sensor . After replace the sensor, reset the the system. Hope this can help.

Posted on May 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is P0113 mean for a 01 merc cougar?


Intake air temperature sensor circuit. It is located between the air filter and engine. Small 2 wire plug. These rarely go bad. Usually it is a wire broke. And they usually break right at the plug.

Apr 15, 2016 | Cars & Trucks

1 Answer

Undefinedas replacement on civic 98 sensor p0113


Possible causes for this code are: - Faulty Intake Air Temperature (IAT) sensor
- Dirty air filter
- Intake Air Temperature (IAT) sensor harness is open or shorted
- Intake Air Temperature (IAT) sensor circuit poor electrical connection. this code sets when: - An excessively high voltage from the sensor is sent to ECM. Usual Possible symptoms - Engine Light ON (or Service Engine Soon Warning Light) P0113 1998 Honda Civic Description The Intake Air Temperature (IAT) sensor is built into mass air flow sensor or in some vehicles mounted to the air filter duct housing. The sensor detects intake air temperature and transmits a signal to the Engine Control Module (ECM).The temperature sensing unit uses a thermistor which is sensitive to the change in temperature. Electrical resistance of the thermistor decreases in response to the temperature rise. The Intake Air Temperature signal is used as an input for various systems in the vehicle.
27782.png

Sep 24, 2014 | 1998 Honda Civic

1 Answer

What does p0113 mean on dodge durango 2002, and how to solve it?


Fault Code Definition
  • Intake Air Temperature Circuit High Input
What does this mean?
The Intake Air Temperature Sensor measures the rise and fall of the air temperature inside the Intake Manifold. This provides critical data needed for the Powertrain Control Module (PCM) to control the Air Fuel Ratio, the Ignition Spark Timing and many components of the Emission Control Systems.
Code P0113 sets when the voltage signal to the PCM from the Intake Air Temperature Sensor Circuit stays above 4.5 volts while the Coolant Temperature Voltage readings are rising and falling within an appropriate range.
Symptoms
  • Check Engine Light will illuminate
  • In some cases, the engine may be hard starting and/or get poor fuel economy
  • Poor engine performance/hesitation on acceleration
Common Problems That Trigger the P0113 Code
  • Defective Intake Air Temperature Sensor
  • Dirty air filter
  • Defective Mass Air Flow Sensor
  • Faulty or corroded Intake Air Temperature Sensor wiring or connections
Common Misdiagnoses
  • Intake Air Temperature Sensor is replaced when the real cause is a dirty air filter
  • Intake Air Temperature Sensor is replaced when the real cause is a poor connection or chafed wiring
  • Intake Air Temperature Sensor is replaced when the real problem is in the Mass Air Flow Sensor
  • P0113 Diagnostic Theory for Shops and Technicians
  • When diagnosing a P0113 code, it is important to record the freeze frame information and then to duplicate the code setting conditions with a test drive while paying close attention to engine load, throttle position, RPM, and road speed on a data streaming scan tool. As you drive the vehicle, compare these values to the Intake Air Temperature Sensor PID or parameter ID. The Intake Air Temperature Sensor voltage values should rise and fall with changes in engine temperature. Compare the Intake Air Temperature or IAT readings to the Coolant Temperature Sensor readings, as they should move in tandem with each other. However, the Engine Coolant Temperature sensor will have a much higher temperature range.
    Check the IAT sensor connector with the key on and the engine off. There needs to be a steady 5 volt reference voltage and a very good ground. Find and use the proper engine performance wiring diagram to discern the proper color and position of these wires in the connector.
    It never hurts to do a key on-engine off voltage output test of the IAT sensor. Typically, I CAREFULLY use a heat gun to raise the temperature of the area around the sensor and study the change in values of the Intake Air Temperature. It's important to use the scan tool data stream as this will verify the IAT harness and connections.

Mar 31, 2014 | 2001 Dodge Durango

1 Answer

Code P0113-P0183


DTC P0113 - Intake Air Temperature Circuit High Input.The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.


DTC P0183 - Fuel Temperature Sensor Circuit High Voltage.


I suggest to check wire connections.

Apr 13, 2012 | 2005 Nissan Quest 3.5

1 Answer

P0113 code for the intake air temperature sensor


Thank you for the inquiry.
P0113
Intake Air Temperature Circuit High Input
P0114 Intake Air Temperature Circuit
P0113 - Intake Air Temperature Circuit High Input

The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.

Potential Symptoms: There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL - Check Engine Light / Service Engine Soon).
Causes: A code P0113 may mean that one or more of the following has happened:
* Internally failed IAT sensor
* Faulty connection at IAT sensor
* Open in IAT ground circuit or signal circuit
* Short to voltage in IAT signal circuit or reference circuit
* IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
* Faulty PCM (less likely but not impossible)

Possible Solutions:
1. First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness connector signal and ground circuits. The IAT temperature reading on the scan tool should be maxed out at the high end. For example it should be 280 degrees Farenheit or higher. If it is, the wiring is okay, and it may have been the connection. 2. If it isn't install the jumper wire between the IAT signal circuit and the chassis ground.
3. If now the IAT reading on the scan tool is maxed out then check for an open in the IAT ground circuit. If you get no reading at all on the scan tool, it's likely that the sensor signal is open or the 5 volt reference is missing. Check using a DVOM (digital volt ohm meter) for a 5 volt reference. If it's there, then unplug the connector at the PCM and check for continuity on the IAT signal circuit between the PCM connector and the IAT connector.


Hope helps; keep us updated and remember to rate this answer

Jun 04, 2011 | Saab 9 3 Cars & Trucks

2 Answers

MOtor is racing code comes upPO113


P0113 - Intake Air Temperature Circuit High Input
The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.

Potential Symptoms: There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL - Check Engine Light / Service Engine Soon).

Causes: A code P0113 may mean that one or more of the following has happened:
Internally failed IAT sensor
Faulty connection at IAT sensor
Open in IAT ground circuit or signal circuit
Short to voltage in IAT signal circuit or reference circuit
IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
Faulty PCM (less likely but not impossible)

Possible Solutions:
First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness connector signal and ground circuits. The IAT temperature reading on the scan tool should be maxed out at the high end. For example it should be 280 degrees Farenheit or higher. If it is, the wiring is okay, and it may have been the connection. If it isn't install the jumper wire between the IAT signal circuit and the chassis ground.

If now the IAT reading on the scan tool is maxed out then check for an open in the IAT ground circuit. If you get no reading at all on the scan tool, it's likely that the sensor signal is open or the 5 volt reference is missing. Check using a DVOM (digital volt ohm meter) for a 5 volt reference. If it's there, then unplug the connector at the PCM and check for continuity on the IAT signal circuit between the PCM connector and the IAT connector.

Hope this helps (remember to rate this answer).

May 06, 2011 | Saturn LW Cars & Trucks

1 Answer

Code po113


P0113 - Intake Air Temperature Circuit High Input

The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.

Potential Symptoms: There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL - Check Engine Light / Service Engine Soon).
Causes: A code P0113 may mean that one or more of the following has happened:
* Internally failed IAT sensor
* Faulty connection at IAT sensor
* Open in IAT ground circuit or signal circuit
* Short to voltage in IAT signal circuit or reference circuit
* IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
* Faulty PCM (less likely but not impossible)

Possible Solutions:
1. First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness connector signal and ground circuits. The IAT temperature reading on the scan tool should be maxed out at the high end. For example it should be 280 degrees Farenheit or higher. If it is, the wiring is okay, and it may have been the connection. 2. If it isn't install the jumper wire between the IAT signal circuit and the chassis ground.
3. If now the IAT reading on the scan tool is maxed out then check for an open in the IAT ground circuit. If you get no reading at all on the scan tool, it's likely that the sensor signal is open or the 5 volt reference is missing. Check using a DVOM (digital volt ohm meter) for a 5 volt reference. If it's there, then unplug the connector at the PCM and check for continuity on the IAT signal circuit between the PCM connector and the IAT connector.


Hope helps; keep us updated and remember to rate this answer.

Mar 02, 2011 | Dodge Ram 1500 Cars & Trucks

2 Answers

P0113


P0113 - Intake Air Temperature Circuit High Input

What does that mean?
The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.

Potential Symptoms
There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL - Check Engine Light / Service Engine Soon).

Causes
A code P0113 may mean that one or more of the following has happened:
* Internally failed IAT sensor
* Faulty connection at IAT sensor
* Open in IAT ground circuit or signal circuit
* Short to voltage in IAT signal circuit or reference circuit
* IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
* Faulty PCM (less likely but not impossible)

Possible Solutions
First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness connector signal and ground circuits. The IAT temperature reading on the scan tool should be maxed out at the high end. For example it should be 280 degrees Farenheit or higher. If it is, the wiring is okay, and it may have been the connection. If it isn't install the jumper wire between the IAT signal circuit and the chassis ground. If now the IAT reading on the scan tool is maxed out then check for an open in the IAT ground circuit. If you get no reading at all on the scan tool, it's likely that the sensor signal is open or the 5 volt reference is missing. Check using a DVOM (digital volt ohm meter) for a 5 volt reference. If it's there, then unplug the connector at the PCM and check for continuity on the IAT signal circuit between the PCM connector and the IAT connector.

Hope this help (remember rated this).

Jun 10, 2010 | 1997 Chevrolet Camaro

3 Answers

Diagnostic codes


P0102 OBD-II Trouble Code - Mass Air Flow (MAF) Circuit Low Input

What does that mean?
Basically this means that there is a problem with the Mass Air Flow (MAF) sensor or circuit. A more technical description would be that the MAF circuit had lower than expected voltage (air flow). Other MAF sensor circuit DTC trouble codes are P0100, P0101, P0103, and P0104.

Symptoms
You will likely not notice any serious drivability problems, although there may be symptoms such as a general decrease in power or sluggishness.

Causes
A code P0102 may mean that one or more of the following has happened:
* The MAF may be disconnected, or a wiring connection may be bad
* The MAF may be dirty or otherwise contaminated (Note: if you use a reusable oiled air filter, be careful not to apply too much oil or that can contaminate the MAF).
* The MAF sensor may be faulty
* The vehicle computer may be faulty (very rare)

Possible Solutions
The simplest thing to do is to reset the code and see if it comes back. Then start with the cheapest, easiest repair procedures:
* Verify that the Mass Air Flow Sensor wiring is connected properly and that there are no broken / frayed wires.
* Inspect for any air leaks near the MAF sensor.
* Take the MAF out and clean it using a spray cleaner such as brake cleaner or electrical contact cleaner. Be gentle with the sensor.
* Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information)
* Replace the MAF sensor.


P0113 - Intake Air Temperature Circuit High Input

What does that mean?
The powertrain control module (PCM) monitors the temperature of the air entering the engine. The PCM supplies a 5 volt reference voltage to the Intake Air Temperature (IAT) sensor. The IAT is a thermistor that varies resistance based on temperature. As the temperature increases, resistance decreases. Low temperature results in a high signal voltage. When the PCM sees a signal voltage higher than 5 volts, it sets this P0113 check engine light code.

Potential Symptoms
There will likely be no symptoms other than illumination of the Malfunction Indicator Lamp (MIL - Check Engine Light / Service Engine Soon).

Causes
A code P0113 may mean that one or more of the following has happened:
* Internally failed IAT sensor
* Faulty connection at IAT sensor
* Open in IAT ground circuit or signal circuit
* Short to voltage in IAT signal circuit or reference circuit
* IAT harness and/or wiring routed too close to high-voltage wiring (e.g. alternator, spark plug cables, etc.)
* Faulty PCM (less likely but not impossible)

Possible Solutions
First, if you have access to a scan tool, is there an IAT reading? If the IAT reading is logical then the problem is likely intermittent. If the reading is less than -30 degrees, unplug the connector. Install a jumper wire between the harness connector signal and ground circuits. The IAT temperature reading on the scan tool should be maxed out at the high end. For example it should be 280 degrees Farenheit or higher. If it is, the wiring is okay, and it may have been the connection. If it isn't install the jumper wire between the IAT signal circuit and the chassis ground. If now the IAT reading on the scan tool is maxed out then check for an open in the IAT ground circuit. If you get no reading at all on the scan tool, it's likely that the sensor signal is open or the 5 volt reference is missing. Check using a DVOM (digital volt ohm meter) for a 5 volt reference. If it's there, then unplug the connector at the PCM and check for continuity on the IAT signal circuit between the PCM connector and the IAT connector.

I really hope help with this (remember rated this).

May 21, 2010 | 2002 Ford Taurus

1 Answer

IAT sensor on 1997 cadillac el dorado


  • P0110 - Intake Air Temperature (IAT) Sensor Circuit
  • P0111 - Intake Air Temperature (IAT) Sensor Performance
  • P0112 - Intake Air Temperature (IAT) Sensor Circuit Low Voltage
  • P0113 - Intake Air Temperature (IAT) Sensor Circuit High Voltage
  • P0114 - Intake Air Temperature Circuit Intermittent ,hope this helps you
  • Jun 14, 2008 | 1997 Cadillac Eldorado

    Not finding what you are looking for?
    2002 Honda Odyssey Logo

    Related Topics:

    172 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    Marvin
    Marvin

    Level 3 Expert

    85222 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22485 Answers

    Jonah Oneal

    Level 3 Expert

    14092 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...