Question about 2005 Ford Explorer Sport Trac
Posted by Anonymous on
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.
The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.
Posted on Apr 02, 2009
Usually located on the frame rail.....
Fuel Filter Removal & Installation To Remove:
Fuel injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before Disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
Posted on Jun 19, 2009
If you can please look under the hood and find the Air filter, and follow that all the way to a round metal part (Throttle body) If you can see it there will be a coil,and on that coid will extrude a curved plate with a cable(throttle cable) attached to it running all the way back inward toward the back of the engine, and next to that there should be a second cable (crusie control cable). This cable is pulled on when you engage the cruise control, by a black box next to the fuse box.
If the Cruise control cable is near by try to reattach it and if it is damaged then have your dealership or some one mechanically inclinded to replace the tip ( if plastic) or replace the cable.
If that didnt help please get back to me
Posted on Jul 16, 2009
if you dont have a ball joint press and dont know how to use one then dont do it, but if you do its not that bad of a job just jack the truck up under the control arm remove the brake rotor then take the lower ball joint nut off then use a pickle fork to break the ball joint loose then take the axle nut off push the axle out of the bearing and use the ball joint press to remove and replace the ball joint
Posted on Jul 19, 2009
They will not loan you the tools.....how else will they continue to rip off the average garage junkie and make lots of money?
Posted on Nov 18, 2009
Tips for a great answer:
Mar 09, 2018 | Ford Cars & Trucks
Jul 31, 2016 | 2007 Ford Explorer Sport Trac
Jan 10, 2016 | 2001 Ford Explorer Sport
Oct 20, 2014 | 2005 Ford Explorer Sport Trac
Jan 28, 2011 | 2005 Ford Explorer Sport Trac
Sep 16, 2010 | 2007 Ford Explorer Sport Trac
Jul 10, 2010 | 2005 Ford Explorer Sport Trac
Mar 31, 2010 | 2005 Ford Explorer Sport Trac
Feb 21, 2010 | 2005 Ford Explorer Sport Trac
Mar 24, 2009 | 2005 Ford Explorer Sport Trac
89 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: