Question about 1993 Toyota Camry V6
TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.
CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
Hope this helps, don't forget to rate.
Posted on Feb 25, 2009
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
some one directed me to autozone.com where i found what i was looking for. it is free once you register your car information. thank you so much.
Posted on May 19, 2009
SOURCE: need marks for timimg belt
On the crankshaft gear there is a VERY small dimple that aligns with a mark on the motor. The mark on the motor (a small triangle) is at roughly 11 o'clock. After you line these timing marks up look at the camshaft gear and you will see that on one of the spokes there is a hole. You need to use a mirror to line this hole up with the dimple on the cover that is behind the camshaft gear. (It is at roughly 1 o'clock) If this hole is 180 degrees from where it should be you need to rotate the motor 1 more revolution at the crankshaft and it should now be lined up, or close. Once lined up I like to take a silver (metallic) Sharpie and make my own mark on the camshaft gear and on the backing plate that is behind it. You can make this mark where ever it is convenient for you. As long as you know where your marks line up, that is all that matters. This way I don't have to use the mirror as often.
Posted on May 26, 2009
Get a T belt from toyota. It has 3 white lines on
it and and arrow mark. 2 lines are solid and one is broken. Put the
arrow facing away from the engine. The cam gears have a dot punched
into them near a certain tooth. This is where the solid white lines
will line up with. The crank gear will have a dot also. It will line up
at 90 degrees from the top, towards the front of the car. This is where
the broken line will match up with. With the belt installed with all
lines on their proper dots and arrow away from the engine, you valve
timming is correct.
Of course you need to remove and compress the tensioner also. I assume you know this already since you didn't ask.
Posted on Apr 16, 2009
loosen the mounting bolts on the alternator, remove the old belt, replace with the new belt, slightly tighten the top mounting bolt, pull the alternator up until the belt is tight or if there is an adjustment bolt, crank down until tight (shouldn't bow more than 1"), and tigten other hardware.
Posted on Aug 12, 2009
Tips for a great answer:
Sep 10, 2016 | 1993 Toyota Camry
Apr 02, 2014 | 1993 Toyota Camry V6
Jul 10, 2012 | 1993 Toyota Camry V6
Sep 11, 2009 | 1993 Toyota Camry V6
Jul 14, 2009 | 1993 Toyota Camry V6
Jul 11, 2009 | 1993 Toyota Camry V6
Jun 26, 2009 | 1993 Toyota Camry V6
Jun 09, 2009 | 1993 Toyota Camry V6
14,210 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: