Question about 2001 Volvo V70

1 Answer

2001 V70 turbocharger pumping oil out exhaust

Recently had car serviced including a veriable valve solenoid gasket replacement, PCV Box reseal and timing belt replaced (2nd time in less than 6 months)due to oil saturation. Was told by mechanic that crankcase pressure causing seal(s) to fail - on the 1st timing belt replacement had oil leak because of cam sensor seal failure. Less than a week after repairs were done, car suddenly started smoking significantly out of exhaust. Towed to back to the shop and was told that a the turobcharger was taking in oil (metioned something about a bearing) and pumping out exhaust. Is this something that the mechanics should have addressed (visable because of the other work they were doing or checked because of the pressure issues and resulting failures of older parts)? The above made up about half of a $2600 bill and the turbocharger work is going to run no less than $1400.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Volvo Master
  • 694 Answers

Bad oil seals in your turbo ! The turbo has to b replaced thanx Chris

Posted on Mar 26, 2017

Ad

5 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 121 Answers

SOURCE: Oil leak above water pump

most prob both, get a new gasket for it and replace that should solve the problem, if not check around the part thats leaking and make sure there is no hair line cracks, but sounds like a bad job did, or it may just need to be tightend up

Posted on Jun 06, 2009

Neil

  • 60 Answers

SOURCE: 98 Volvo V70 GLT - Oil Pump or Valve Job?

Most common cause of ticking in these is the oil pick-up seals. Remove the pan and replace the oil pick-up tube seal, the two seals for the tube in the pan and the 2 O-rings on the right side of the pan. And dont use silicone to seal the pan back up, because it WILL leak, I highly recommend the Volvo sealant

Posted on Oct 26, 2009

sporeda3

  • 125 Answers

SOURCE: oil pressure warning on 2001 Volvo v70 with 220Km

The best way to attack this is to have your oil pressure checked. That would rule out a pump problem or the sender issue. If you want the least expensive fix is to just replace the oil pressure sender yourself and then see if the problem goes away. You can also add a thicker oil when you change the oil to see if that solves the problem. A 10W30 oil is thinner than a 10W50. If this helps then the engine or pump may be worn or failing. I hope the cheap fix helps!!

Posted on Jan 24, 2010

geoff hunter

  • 4793 Answers

SOURCE: had timing belt replaced in 1/2010 for 2001 volvo s80.

yes,the water pump should have been changed at the same time,BUT,and i keep saying this to all my customers,no garage will do any work that you, the client, dont ask for and if they reccomend it they are trying to rip you off.the original repairperson is not at fault in any way,as you cant see inside the pump to decide when its going to fail.....not what you wanted to hear ,but true.
best advice.is find a good mech and follow him/her around,that way it becomes personal.

Posted on May 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

05 Hyundai sonata 2.7 started missing all the sudden and vibrates/shakes real bad when idling MIL on giving p0305 code why?


Possible causes
  • Faulty spark plug 5
  • Clogged or faulty fuel injector 5
  • Faulty ignition coil 5
  • Fuel injector 5 harness is open or shorted
  • Fuel injector 5 circuit poor electrical connection
  • Ignition coil 5 harness is open or shorted
  • Ignition coil 5 circuit poor electrical connection
  • Insufficient cylinder 5 compression
  • Incorrect fuel pressure
  • Intake air leak


you need an odb2

Jun 17, 2017 | Hyundai Cars & Trucks

1 Answer

How to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve engine


Choose:

1994 Mazda MPV timing belt replacement, 6 cylinder DOHC ...

? 3:46
https://www.youtube.com/watch?v=sD2G-NzycvU
Aug 11, 2011 - Uploaded by rsarp
1994 Mazda MPV timing belt replacement, 6 cylinder DOHC 3.0... engine so the valves would not be bent ...

How to replace the timing belt on a 1994 mazda 929 3.0 ...

www.fixya.com/.../t25991928-replace_timing_belt_1994_mazda_929_3...
4 hours ago - how to replace the timing belt on a 1994 mazda 929 3.0 dohc 24 valve... I have a 2000 Mazda 626 4cyl 2.0 liter DOHC engine replacing the timing belt, what ... 2004 6s, 3l. where is the canister purge valve solenoid located?

Where are the timing marks on a 1994 mazda 929 3.0l - Fixya

www.fixya.com/cars/t25991952-timing_marks_1994_mazda_929_3_0l
4 hours ago - where are the timing marks on a 1994 mazda 929 3.0l - Mazda Cars ...1994 Mazda E2000 Cam Timing Mark Positions to Replace Timing Belt ... on a 1994mazda v6 dohc 24 valve engine How to align the timing mark on the ...

Mazda Timing Belt Replacement



Dec 03, 2015 | Mazda Cars & Trucks

2 Answers

Where is the ac port located on a1997 honda passport


follow the ac lines after the condenser before they go into the firewall and you will find the ports for low and high side.

I’m happy to assist further over the phone at https://www.6ya.com/expert/josh_8f8ad0a8f7e0e6d3

Jul 07, 2015 | Honda Cars & Trucks

2 Answers

Timing belt broken kia rio 2003


it is an interference engine which means that when a belt breaks , you can expect at least half of the valves to be bent and need replacing
you can get more quotes for the job as that seems extreme
the work entails replacing the belt , idler pulleys , cam and crank seals and hydraulic adjuster ( a professional job to get another 60,000miles from the belt)
That much will set you back by around $1000.00 including labour
The extra is the head removal and new valves so add another $700.00 --including labour )for that and you can see that you need more quotes from accredited service shops

Sep 12, 2017 | Kia Cars & Trucks

2 Answers

What services does camry 2000 with 90000 km need


90000 km service includes changing.spark plugs,oil and oil filter,gearbox fluid,brake fluid ,air filter and fuel filter if needed,a full safty inspection.and the most important timing belt,and while your doing the timing belt you should do the water pump.

Oct 18, 2009 | 2003 Toyota Camry

1 Answer

CEL on; no error codes.. I havent tried hooking up a obd code checker. The problem I'm having is a hesitating idle. Every time I rev the engine a little is seems as if im running on 3 cylinders or...


check compressions ,,,,could be dodgy valve seats ,wouldnt be the first time i have seen all this changed ,then vehicle comes to me and badly burnt valve seats are what i find ,new gasket and regrind of the valves and the vehicle leaves me driving like a new motor

Sep 15, 2009 | 1992 Honda Accord

1 Answer

What is the average cost for a tune up on a 2005 Jaguar Type S 3.0--6 cylinder?


System, Tune-Up B 0.0 3.8 Notes Includes: Renew & Adjust Spark Plugs. Inspect Or Replace Distributor Cap, Rotor & Ignition Cables (Where Applicable). Service Or Renew Air, Fuel Filter And PCV Valve. Adjust Ignition Timing And Check Advance. Make Necessary Fuel Adjustments, Service Battery. Does Not Include: Adjust Belts.labor book gives 3.8 hrs x labor rate of the shop. parts will vary depending if they are Jaguar parts or after market

Aug 06, 2009 | 2005 Jaguar S-Type

2 Answers

1995 nissian pickup 4 cly


replace gasket put a pcv valve in it

May 14, 2009 | 2005 Chrysler Town & Country

1 Answer

How do i tighten the timing belt on a v-6


the timing belt adjuster is automatic
if there is slack, the belt is beyond its service limits and should be replaced before failure
timing belt failure includes severe engine damage
belt breaks
crankshaft continues to rotate
camshafts stop
one or more valves jam open,
jammed valves smash the piston crown on the next upstroke
large fragments of steel destroy the bottom end

Engine $thousands or Belt and adjuster kit $200

Oct 14, 2008 | 1992 Mazda MX-3

Not finding what you are looking for?
2001 Volvo V70 Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...